2 X Zanussi’s

Home › Forums › Trade Technical & Spare Parts Forums › Trade Technical Enquiries › 2 X Zanussi’s

Viewing 13 posts - 1 through 13 (of 13 total)
  • Author
    Posts
  • October 27, 2009 at 4:11 pm #49650
    Toni
    Participant

    Hi I have 2 Zanussi machines giving me a headache
    The 1st one is a ZWF12070W1
    This one just pumps all the time as soon as you press the start button.
    I have checked the heater & the machine in general for any earth faults, and also disconnected the pressure hose to the analogue p/switch

    The 2nd is a ZWD 1252W
    this one fills & starts to wash, then after a couple of minutesit stops with the start light flashing (No other lights)
    the drum turns ok, it drains ok and it will spin if put on a spin (If put on these programs). Not been to this one yet

    Any help would be appreciated
    Toni

    October 28, 2009 at 11:09 pm #300574
    leavemetogetonwithit
    Participant

    Re: 2 X Zanussi’s

    ZWD1252 could be drier element down to earth.
    Hope you get some help with the other one cause I’ve got similar booked in Friday afternoon.
    Mike.

    October 28, 2009 at 11:13 pm #300575
    helo_75
    Participant

    pcb fault every time :S

    October 29, 2009 at 4:18 am #300576
    gandh1
    Participant

    Re: 2 X Zanussi’s

    have had a blocked sump cause the 1*070 range to go into a kind of safe mode. where it stuck in pump cycle. even after you clear the obstruction it will stay like this. cynically i think its there so the cleverer diy customer gives up and calls zanussi out.

    once i cleared the sump of foreign (literally) coins, if you access diagnostics, run their component test all the way through, and alls ok, and exit it, it seems to clear the memory chip and alls well. well so far for the last 4 months…

    might be worth accessing diagnostics and seeing what error code is thrown up before assuming pcb failure…

    October 30, 2009 at 8:48 pm #300577
    leavemetogetonwithit
    Participant

    Re: 2 X Zanussi’s

    Went to ZWD12270W today. Was doing nothing but constant pump on all progs. Then she mentioned, “oh, and the drier gave up some time ago”. I measured the element, it was OK for continuity and 19 megs IR. Disconnected it anyway and machine sprang back to life!
    I’m thinking these Zan electronics get upset very easily. They really should do something about it if they want to keep their reputation.
    Mike.

    November 1, 2009 at 12:10 am #300578
    gandh1
    Participant

    Re: 2 X Zanussi’s

    its a “safe mode” in order to avoid damaging other components, if somehting becomes faulty it will basically shut down… until you fix i, and clear the error memory!

    November 1, 2009 at 12:51 am #300579
    leavemetogetonwithit
    Participant

    Re: 2 X Zanussi’s

    Hmm, didn’t have to clear the memory on mine. Maybe I’ll be having a callback next week? Not to worry, going by that way anyway.
    Mike.

    November 1, 2009 at 11:21 am #300580
    cornwell40
    Participant

    Re: 2 X Zanussi’s

    Tried everything on one recently with constant draining. Giving a spurious fault code didn’t help either. After speaking to the Oracle (no not Johnny Vegas) at the local service Force there has been a memo about corrupted boards doing just this. Put a new one in and has been fine since…..so I’d agree with Helo on this one.

    TC

    November 1, 2009 at 2:08 pm #300581
    helo_75
    Participant

    i dont say these things for a laugh ya know, i see them from day one remember

    just for reference, its worth checking the door lock as well

    November 1, 2009 at 8:10 pm #300582
    rolf
    Participant

    Re: 2 X Zanussi’s

    (Helo wrote I dont say these things for a laugh ya know)……Helo…..You crack me up.lol 😆

    November 1, 2009 at 8:11 pm #300583
    helo_75
    Participant

    job done then eh 😀

    November 24, 2009 at 4:40 pm #300584
    Jonah
    Participant

    Re: 2 X Zanussi’s

    Hey lads just had a ZWD12270W today no supply to the dryer heater when drying, changed dryer PCB still the same, changed main PCB still no supply to dryer element, live supply on both sides of the main thermostat but no supply to the reset stat or element.

    Checked filter all clear, checked continuity on connections from PCB’s to heater all ok, this one has me stumped, any help appreciated 😕

    November 24, 2009 at 6:37 pm #300585
    Penguin45
    Participant

    Re: 2 X Zanussi’s

    Check lower dryer NTC.

    Chris.

  • Author
    Posts
Viewing 13 posts - 1 through 13 (of 13 total)
  • You must be logged in to reply to this topic.