Forum Replies Created
-
Posts
-
Re: Hoover 1200 NW – All Lights a Flashin Baby ! Help !
Incidentally – I found IC5 on the panel to have some corrosion on the pins.
I’ve ordered a replacement MM74C14N Chip and will replace….will let you know how it goes.It aint the heater – works fine. Also silicone sealed the drum and rubber to stop that nasty firestarting drip.
Cheers for the advice guys.
Ron.
Re: Hoover 1200 NW – All Lights a Flashin Baby ! Help !
Too boot I just got a –
Sorry no engineers in your area off the link anyway….
Need to get it sorted – wife 5 months preggers and I’m of to spain saturday – Eeek –
Re: Hoover 1200 NW – All Lights a Flashin Baby ! Help !
Cheers for the help chaps.
I’ll go home and do the heater test later.
Failing that I’ll check the connections etc…I’m an Electronics eng by trade so would have thouyght myself capable with the right pointers….?
Cheers again.
Much appreciated indeed.
Ron.
Re: Hoover 1200 NW – All Lights a Flashin Baby ! Help !
Hi Martin,
Thanks for such a prompt reply.
Yes, the machiune goes on, program set – hit the start and the water rushes into the tray and the drum rotates. No strange noises or anything – all looks a ok.
Then 30 mins or so into the program, the drum stops as does everything and all the LEDS flash continuosly however no error code appears on the LCD.
Does that help ?
Re: Hoover 1200 NW – All Lights a Flashin Baby ! Help !
Finally ! made it home and back…
Serial number is indeed
A8608 3030 1176.
Cheers in advance of any help !
Ron.
RS wrote:Ron you still haven’t put the model number up, listen to Martin he does this for a living 🙂
PS Check your email from James
Gottcha – Thanks.
Re: Hoover 1200 NW – All Lights a Flashin Baby ! Help !
Sorry Guys – Logged off last night till this mornin and that means I’m going to have to go hame at lunch and get the whole number …..
Will sort it by 12.00….
Re: Hoover 1200 NW – All Lights a Flashin Baby ! Help !
well just tried all the programs i could in an effort to see if any are ok but the flashing thing happens with em all…..
Off to make some dinner…back tommorrow…
Re: Hoover 1200 NW – All Lights a Flashin Baby ! Help !
Hi Yurtesen,
Thanks for the reply…
I’ll try a cold wash and see what happens. Good thinking.
As to the lights –
On 1 second off 1 second continuously till power off and on.
Manual – or rather little book that came with it say nothing of troubleshooting or faults…just says call the hoover service line….
Thanks again.
Ron,
Re: Hoover 1200 NW – All Lights a Flashin Baby ! Help !
Hi Yurtesen,
Thanks for the reply…
I’ll try a cold wash and see what happens. Good thinking.
As to the lights –
On 1 second off 1 second continuously till power off and on.
Manual – or rather little book that came with it say nothing of troubleshooting or faults…just says call the hoover service line….
Thanks again.
Ron,
Re: Hoover 1200 NW – All Lights a Flashin Baby ! Help !
Well I made it home at last ! Traffic in Liverpool is crazy with all the capital of culture road changes….
Anyway ! Serial Number is L8608 if that is of any help or use….
isnt it weird – I searched the web for the new wage and the fire service said that there was a recall on em due to some overspill fault with the detergents….glad it only affected the earlier models to ours !
Warm water – mmm but if it were a 60 degree wash cycle wouldnt it be a little hotter ? so does that mean its taking only the pipe water in and not heating it, pointing directly to the heater ?
Am I close at all ? (about to start taking it appart to check blockages)….?
Thanks again in advance …
Ron.
Re: Hoover 1200 NW – All Lights a Flashin Baby ! Help !
LMAO – This could get funny !
OK, on my way home now … so to elim the heater would I have to replace it or is there a test ?
Could still have a wager on it …. 😆
Re: Hoover 1200 NW – All Lights a Flashin Baby ! Help !
Ekk – 2 Replies ! 🙂
I’ll get the model number in an hour ….
How can I eliminate these components ?
Just thought – when I put my hand in front of the waste pipe – it were warm, not hot…,,,mmm – could that be an indication ?
Re: Hoover 1200 NW – All Lights a Flashin Baby ! Help !
Martin wrote:Model number please Ron????
Martin
Sorry Martin – I got to go home and get it…. 😳 I thought “New Wave”
was the model…..I’ll log on from home at about 17.00 and add it to the thread.
Rather embarrassed !
Thanks for such a speedy response.
Ron.
