These fault codes are for Fagor washing machine models that use a digital display using what Fagor term the V3, V4 and V5 electronic controls so, these erorr codes cover a number of Fagor produced washing machines.
Before you start any investigation of the fault or even remove the lid of the washing machine or washer dryer please read and fully understand this article in full and pay particular attention to the safety and information notices at the bottom of this page as they contain extremely important information!
Please remember to support our site by buying Fagor washing machine spares from our store here and, if you decide that you really need an engineer please support the local repairers that help make this site possible, you can search for a Fagor washing machine repairer using the engineer search.
Fagor spare parts and support may be limited since the group collapsed in 2013.
Fagor Washing Machine Fault Codes
These fault codes are written for washing machine repairers and not for the general public by Fagor and they assume a certain level of competence on the part of the user in diagnostic routines. We have added some notes to try to assist you in determining the nature of the fault you have but, you will still need to investigate each failure on its own merits. For more help and advice on fault finding on a washing machine please refer to our washing machine fault finding guide from this link before you begin.
If you struggle or cannot find the appropriate fault code that you need for your Fagor machine please ask in the forums and the gusy there will do what they can to help and locate the meaning of the fault code you need
Please check that any Fagor washing machine spares recommended are suitable for use on your particular model and serial number. If you are unsure about the suitability of any spare part please ask to ensure that you get the correct spares for your washing machine or washer dryer. Please, don’t guess or assume as spares can be altered on a production run with the same model number having several different alternative components used.
F01 |
Not filled in time allowed (8 Minutes) – washing machine does not fill
|
F02 |
Not drained in time allowed (6 minutes) – washing machine fails to drain water
|
F04 |
Door safety lock error
|
F05 |
NTC fault – temperature sensor detected as either open circuit or shorted
|
F06 |
Water heating error detected – Failed to heat for 15 minutes
|
F07 |
Overfill or drain pump not in circuit
|
F08 |
Motor fault detected – tacho generator error
|
F09 |
Motor detected as not reversing
|
F10 |
Communication error between electronic control boards and wiring
|
F11 |
Communication error between boards and wiring
|
F12 |
Communication error between electronic control boards and wiring
|
F13 |
Flow meter fault – not detected
|
F14 |
Pressure sensor fault – not detected
|
C03 |
Out of balance protection activated
|
Fagor Washing Machine Spares
Fagor Group appliances are found using two key pieces of information, what the washing machine model number is and the serial number from the rating plate. We can often find them from the model number because we can eliminate multiple instances on occasion and, we know what we’re looking at and for, you often won’t. But, even with our knowledge even we will often need the serial number or production code to identify the washing machine correctly and, accordingly, the spares required.
Our advice is very simple, don’t guess at it and end up with the wrong parts, contact us from this link and check that you are ordering the correct Fagor spares.
More Fagor Washing Machine Help, Advice And Guidance
Should you need more help and guidance please use the links from this article as most of them will help you to understand your Fagor washing machine a lot better and probably very much help you in diagnosing the fault you have. Of course there are many other articles on the site that will also help you do this.
In addition you can post in our washing machine forum after registering but please do pay heed to the information below before doing so and read the guides, they are there to help you.
You must understand certain things before you begin or attempt any repairs on your own and we want to make these points very, very clear to anyone that decides to investigate one of these or any other washing machines:
- We are not responsible for your safety, you are and by using this guide you accept that and accept that any damage that you may cause and work undertaken is entirely at your own risk.
- We will advise the common causes of the fault codes but we cannot guarantee that any parts or work recommended will resolve the issue. It is entirely your responsibility to diagnose your particular problem and resolve it.
- We are not responsible for you buying spares that do not resolve the problem, this is down to your own diagnosis not ours.
- No warranty is inferred, implied or given.
You also have to understand that fault or error codes are not a “magic bullet”, they will not tell you what the problem is, they will only offer you an indication of where the problem lies and they are no substitute for good old fashioned diagnostic skills. You can find out more about what fault codes actually tell you in this article. So please be well aware that, even with this new found knowledge you will still have to actually be capable of investigating and diagnosing the problem and this means adhering to basic appliance safety for working on them.
Please do note that manufacturers can and do change fault codes without notice and we cannot guarantee that these error codes will apply to your particular model as all codes apply to a wide range of appliances and not normally any one specific model. To determine if these fault codes do apply to your particular Fagor washing machine or washer dryer model please post a request to confirm this in the forums.

we resived tg signal error on the disply washer model1f-4613x what is problm pls hlpe me
Keep filing up . It. Is ok when power is on but when I select A program to fill it carriers on filling. If I switch power on of it stops
Our Fagor innovation works fine, but has stopped taking fabric conditioner. You have to tip the tray when it is rinsing and that is the only way to get it into the machine. Can you please advise anything. Many thanks.
I put number 2 on the machine setting
That means it will wash 30mins but it keeps on stopping with a sign F 02. What this means?