Beko Fault Codes
This set of fault codes only pertains to the Beko WM series of washing machines but it may also relate to other Beko models that use the same PCB from Invensys for a controller and have five LEDs used.
These error codes may not relate to ALL Beko WM series washing machines. If you are unsure please ask in the forums as well as for all other Beko washing machine fault codes.
Before you start any investigation of the fault or even remove the lid of your Beko washing machine please read and fully understand this article in full and pay particular attention to the safety and information notices at the bottom of this page as they contain extremely important information!
Please remember to support our site by buying Beko washing machine spares from our spare part store and, if you decide that you really need an engineer please support the local repairers that help make this site possible, you can search for a repairer from theengineer search facility.
Beko 5 LED Washing Machine Fault Codes
These fault codes are written for washing machine repairers and not for the general public by Beko and they assume a certain level of competence on the part of the user in diagnostic routines. We have added some notes to try to assist you in determining the nature of the fault you have but, you will still need to investigate each failure on its own merits. For more help and advice on fault finding on a washing machine please refer to our washing machine fault finding guide from this link before you begin which will help you diagnose the problem with your Beko washing machine.
If you struggle or cannot find the appropriate fault code that you need for your Beko machine please ask in the forums and the gusy there will do what they can to help and locate the meaning of the fault code you need
Please check that any Beko washing machine spares recommended are suitable for use on your particular model and serial number. If you are unsure about the suitability of any spare part please ask to ensure that you get the correct spares for your washing machine. Please, don’t guess or assume as spares can be altered on a production run with the same model number having several different alternative components used.
Fault Code Lights Legend
This is our very simple legend to show the state of the lights, lamps or LED’s as they are unlit, flashing or lit continuously.
 |
Light or LED not lit |  |
Light or LED flashing |  |
Light or LED lit solid, no flash |
Beko Washing Machine Fault Codes
The LEDs in these error codes represent the prewash, spin, rinse and then wash LED’s as you look at them, being either lit or not lit, they should not be flashing.
H1 |
|
|
|
|
|
NTC (thermistor) Open or Short CircuitThe washing machine has detected an error with the wash thermistor and is reporting this. The error can be caused by either a short circuit or the thermistor itself being open circuit.
|
H2 |
|
|
|
|
|
Heater detected open circuitOrdinarily this is the indication of a simple heater failure however it may pay to check the wiring and thermistor.
|
H3 |
|
|
|
|
|
Heater detected as always onThe wash heater is detected as being on constantly in the washing machine and the machine will abort and shut down.
|
H4 |
|
|
|
|
|
Water inlet valve triac short circuitThe electronic control module has detected a fault in the water inlet valve control triac, namely that it has a short circuit.
|
H5 |
|
|
|
|
|
Drain pump detected open circuitOrdinarily this will be indicative of a simple drain pump failure.
|
H6 |
|
|
|
|
|
Motor triac shortThe electronic controller has detected a short circuit on the motor control triac but there are other things to check.
|
H7 |
|
|
|
|
|
Pressure sensor failureThis error is the electronic controller detecting that there is a failure of the pressure or level sensor however, it can also be caused by an errant reading or signal causing the failure to be detected.
|
H11 |
|
|
|
|
|
Motor open circuitThis error can be caused by the motor being oppen circuit or the motor tacho being detected as open circuit. Both can be cause by wiring or connection issues.
|
More Help For Beko Washing Machines
Should you need more help and guidance please use the links from this article as most of them will help you to understand your Beko washing machine a lot better and probably very much help you in diagnosing the fault you have. Of course there are many other articles on the site that will also help you do this.
In addition you can post in our help and advice forums after registering but please do pay heed to the information below before doing so and read the guides, they are there to help you.
You must understand certain things before you begin or attempt any repairs on your own and we want to make these points very, very clear to anyone that decides to investigate one of these or any other washing machines:
- We are not responsible for your safety, you are and by using this guide you accept that and accept that any damage that you may cause and work undertaken is entirely at your own risk.
- We will advise the common causes of the fault codes but we cannot guarantee that any parts or work recommended will resolve the issue. It is entirely your responsibility to diagnose your particular problem and resolve it.
- We are not responsible for you buying spares that do not resolve the problem, this is down to your own diagnosis not ours.
- No warranty is inferred, implied or given.
You also have to know that fault or error codes are not a “magic bullet”, they will not tell you what the problem is, they will only offer you an indication of where the problem lies and they are no substitute for good old fashioned diagnostic skills. You can find out more about what fault codes actually tell you in this article. So please be well aware that, even with this new found knowledge you will still have to actually be capable of investigating and diagnosing the problem and this means adhering to basic appliance safety for working on them.
Please note that manufacturers can and do change fault codes without notice and we cannot guarantee that these error codes will apply to your particular model as all codes apply to a wide range of appliances and not normally any one specific model. To determine if these fault codes do apply to your particular Beko washing machine model please post a request to confirm this in the forums.
Problem with programmer beko WM74135W
hi my washing machine turns once then stops won’t spin but does drain can you tell me what is wrong please many thanks
Very possibly the motor carbon brushes but without a lot more information it’s almost impossible to say.
hi when i put my washer on it trips the electric we have changed the fuse plug checked the socket and still keep blowing the electrics in the house …
my washing machine fills, does not spin but i hear it clicking through the programs, then it emptys
beko wma765w spin does work but will spin in all washed what up with not reading any codes on the spin progam it go fro 19m t0 1m in 30sec and all pumps and motor working fine
Hi, I have got Beko WMA 765 S washing machine. When I try to switch it on, it starts flashing on the spin speed 1200, the pause lit solid and on the display you can see like: IL., and this “I” is flashing. It happenned during the last wash. If somebody knows what it is, please help me.ps. I have tried to reset it, but after every reset the no spin led is flashing. When I turn it off and on again, it starts the same story as above again.
My Beko washing machine door does not open
My beko wm5100w wont start, the start and wash lights are on but it does nothing. Will spin, fill and drain in test mode but again nothing when wash light is on. Any suggestions?
[quote name=”Rjsmith”]My beko wm5100w wont start, the start and wash lights are on but it does nothing. Will spin, fill and drain in test mode but again nothing when wash light is on. Any suggestions?[/quote] mine is doing the same thing as yours, it rinses also mine just wont do the wash, even does a pre wash,
My beko dishwasher lights are not working, it was just doing a pre wash not heat no detergent the buttons to change programme has no lights so can’t see if programme changing. I have turned it on/off many times to see if it had changed programme to wash but still only doing a pre wash! I then tried to reset it as beko suggests and now still no lights to indicated and it’s starting fine then says end but now not even doing a pre rinse/ wash.Do I get a new pcb board or ? Please advise many thanks.
Please advise.My beko dishwasher lights are not working it has just been doing a pre rinse which I have tried to change but no lights to indicated as to what program it’s on so I keep trying to change the programme.But still only doing pre wash. How can I tell if I need new pcb board?Any help is appreciated.
Yesterday my washing machine beko wmb91442lw started to make a funny noise. Then it stopped letting any water out. I opened the overflow bit to see if there was any lime scale or hair or anything else in there. But there was a spindle that wasn’t attached to anything. Is this a recall problem? The machine was brought at the very end. March 2013. Would be grateful for any advise. Thanks.
I have a Beko machine and it’s showing spin/end light which won’t come off…so every time we try to put a load on it won’t go to start the cycle.
hi, WMB91442LW runs through the prewash/wash cycles and ends with 30 odd mins left. No rinse or spin. One engineer has suggested the waste hose blocked (checked and found nothing) and another says the board at fault. the machine is 14 months old and 2 months out of guarantee. Could it be a H7 fault
My Beko washing machine every so often starts a wash with a hot wash of over 2 hours when a quick wash was selected, no other display apart from time of wash. Can anyone else advise of this problem or how to fix it.
My Beko washing machine will not wash or spin,all I get is the padlock showing on the screen,I have tried to reset but just keeps doing same as before.
my beko washing machine does washes ok but not hot wash is this a fault
My beko washing machine eco wmb 81445 LW is filling and emptying but nothing else while padlock symbol flashes intermittently,can anyone help?
[quote name=”rob mills”]My beko washing machine eco wmb 81445 LW is filling and emptying but nothing else while padlock symbol flashes intermittently,can anyone help?[/quote]turn on the machine while holding the start stop button, make sure the knoc is on the cotton setting this should give you an error code.