Blomberg Fault Codes

These fault codes were used on German made Blomberg washing machines while the company was owned by the French company Brandt. When Brandt was broken up Blomberg was ultimately was sold off to Beko, these fault codes will not apply to later Beko built washing machines with a Blomberg badge on them.
These error codes will also apply to some Brandt badged washing machines as well.
Before you start any investigation of the fault or even remove the lid of your Blomberg washing machine or washer dryer please read and fully understand this article in full and pay particular attention to the safety and information notices at the bottom of this page as they contain extremely important information!
Please remember to support our site by Blomberg washing machine spares from our spare part store and, if you decide that you really need an engineer please support the local repairers that help make this site possible, you can search for a Blomberg washing machie engineer using our engineer search facility.
Blomberg Washing Machine Fault Codes
These fault codes are written for washing machine repairers and not for the general public by Blomberg and they assume a certain level of competence on the part of the user in diagnostic routines. We have added some notes to try to assist you in determining the nature of the fault you have but, you will still need to investigate each failure on its own merits. For more help and advice on fault finding on a washing machine please refer to our washing machine fault finding guide from this link before you begin which will help you to diagnose the problem with your Blomberg washing machine.
If you struggle or cannot find the appropriate fault code that you need for your washing machine please ask in the forums and the gusy there will do what they can to help and locate the meaning of the fault code you need
|
01 |
Water inlet fault detected – washing machine will not fill
|
|
02 |
Drain error detected – washing machine will not drain
|
|
03 |
Heating error detected – washing machine will not heat water
|
|
04 |
Motor triac shorted
|
|
05 |
Temperature NTC error detected
|
|
06 |
Motor tacho fault
|
|
07 |
Door latching or lock error
|
|
09 |
Program selector fault
|
|
10 |
Overfill detected – washing machine fills with too much water
|
|
11 |
Water heating fault detected – washing machine does not heat water
|
|
12 |
Door latch fault detected
|
|
13 |
Spin speed error detected
|
|
18 |
Incorrect mains frequency or voltage
|
More Blomberg Washing Machine Help
Should you need more help and guidance please use the links from this article as most of them will help you to understand your Blomberg washing machine or washer dryer a lot better and probably very much help you in diagnosing the fault you have. Of course there are many other articles on the site that will also help you do this.
In addition you can post in our forums after registering but please do pay heed to the information below before doing so and read the guides, they are there to help you.
You must understand certain things before you begin or attempt any repairs on your own and we want to make these points very, very clear to anyone that decides to investigate one of these or any other washing machines:
- We are not responsible for your safety, you are and by using this guide you accept that and accept that any damage that you may cause and work undertaken is entirely at your own risk.
- We will advise the common causes of the fault codes but we cannot guarantee that any parts or work recommended will resolve the issue. It is entirely your responsibility to diagnose your particular problem and resolve it.
- We are not responsible for you buying spares that do not resolve the problem, this is down to your own diagnosis not ours.
- No warranty is inferred, implied or given.
You also have to know that fault or error codes are not a “magic bullet”, they will not tell you what the problem is, they will only offer you an indication of where the problem lies and they are no substitute for good old fashioned diagnostic skills. You can find out more about what fault codes actually tell you in this article. So please be well aware that, even with this new found knowledge you will still have to actually be capable of investigating and diagnosing the problem and this means adhering to basic appliance safety for working on them.
Please do note that manufacturers can and do change fault codes without notice and we cannot guarantee that these error codes will apply to your particular model as all codes apply to a wide range of appliances and not normally any one specific model. To determine if these fault codes do apply to your particular Blomberg washing machine model please post a request to confirm this in the forums.

I cannot find the serial number on new washing machine to activate guarantee
Hi Penny,It should be on a sticker inside the door of your washing machine.
my washer machine show a code error “c on” and d’ont work anymore. what can i do? i d’ont find find local service
The fabric softener is not being transferred into the machine. It remains in the drawer. We have cleaned the drawer thoroughly.
If you have a read of the article on fabric softener issues it should explain the main causes of problem with that for you.
My new washing machine that’s I just bought shoes Code E02 – what should I do
I bought a refrigerator: Blomberg brand (model KQD1440X) and it is suddenly giving me an error 8 on the display. However, when I turn the ice maker off the error disappears. The ice maker and water are working properly but the err 8 is persistent. Also, I cannot remove the ice container it seems jammed.
Please help me understand?
My Blomberg washing machine intermittently come up with the code L and then a backward L can anyone help me to work out what’s wrong with it? It’s still working though!