“Ooooh Matron” ?

[Penguin45]

Re: Anguis in herba

Ok, this one:
http://www.ukwhitegoods.co.uk/modules.p … 9610#99610
was getting a bit disorganised – I have perhaps said more than I should, but if “pto” adds to it please kick his back side. I have finished the post “that is all”, after all.

That is all…….. 😀
:p45:

[Martin]

Re: Anguis in herba

Well our madrat is leaving his mark all around the forums I must say 😕

http://www.ukwhitegoods.co.uk/modules.p … sc&start=0

http://www.ukwhitegoods.co.uk/modules.p … ic&t=17568

[Penguin45]

Re: Anguis in herba

I really actually rather enjoyed the dishwasher one…… Haven’t given anyone a good kicking in ages 😀
Chris.

[gegsy]

Re: Anguis in herba

Another know it all feckwit PatrickB
First post has dismantled an in warranty Admiral F/F and then proceeds to slag the engineer off after his visit:rolls:
http://www.ukwhitegoods.co.uk/modules.p … 448#100448
Greg

[gegsy]

Re: Anguis in herba

Have just deleted whitevanmans last post in http://www.ukwhitegoods.co.uk/modules.p … 465#100465
for posting the below

step
1. power off appliance
from the front
2. remove shelves from oven
3 remove baffle plate screws 4 in total
4 get 10mm spanner and remove nut from fan
5 remove 3 nuts 7mm
6 pull appliance out using jacking tool
7 pull appliance out (take care with cable & gas pipe if df
from rear
8 large cover remove screws
9 disconect wires (remembering colours eg eath wire
10 remove large round housing with fan attached
11 remove fan from ass and rebuild using fan supplied
12 line up 3 studs with back wall of oven
13 return to front an follow steps in reverse 2 – 5
14 now fit rear plate

Note
You should always perform a insulation test prior with a meggar prior to powering appliance back on

hope this helps
Wvm

Hope that ok

Greg

[kwatt]

PM him to inform and the whys.

K.

[gegsy]

Re: Anguis in herba

Sorry already done hope this was ok

Outbox :: Message
From: gegsy
To: whitevanman
Posted: Wed Sep 20, 2006 10:41 pm
Subject: Too much information in Public Forum

Hi
Im sorry but I had to remove your post in the Cooking Forum.
The information was too indepth and we as Trade Members on here are not allowed to give a blow by blow account of how to fix an appliance.
It also leaves you exposed to being sued if anybody else of less capability reads the forum and injures themselves.

Regards

Greg

[iadom]

Re: Number 2 is watching.

[iadom]

Re: Number 2 is watching.

Has beno had permission to post a link to his own website, I know it is in his profile.
❓
http://tinyurl.com/gp6vy

Perhaps we could interest him/her in a sponsorship package. 😉

[gegsy]

Re: Number 2 is watching.

Blatant advertisement but is in Trade Forum Jim so I can’t see any problems with it 😕 😀

Greg

[iadom]

Re: Number 2 is watching.

Agreed, but the OP was after a trade supplier for graded/new etc. That site is aimed at Joe Public, and checking the prices, it is not that competitive.

Jim.

[kwatt]

If he does it repeatedly then there’s a problem, in effect he should pay to advertise. If however he’s answering the question with an answe as is the case here then there’s not.

Confusing isn’t it? 😉

K.

[gegsy]

Re: Number 2 is watching.

[Penguin45]

Re: Number 2 is watching.

But, he was Number 1 all along…….
C.

[gegsy]

Re: Number 2 is watching.

Penguin45 wrote:But, he was Number 1 all along…….
C.

He sure was but wasn’t he No6 not 2 😕

[Author]

Posts