gegsy

Forum Replies Created

Viewing 15 posts - 3,736 through 3,750 (of 6,724 total)
1 2 3 … 249 250 251 … 447 448 449
  • Author
    Posts
  • October 31, 2006 at 5:42 pm in reply to: Whirlpool G2PDWI/1WH help…. #193785
    gegsy
    Participant

    Re: Whirlpool G2PDWI/1WH help….

    Hi it sounds like the NTC has gone faulty. This is mentioned in numerous posts.
    The p/no if you should need is 481228268035.
    Power off if you plan on tackling this yourself or please feel free to use the link below to find an engineer. 🙂
    HTH

    Greg

    October 31, 2006 at 5:39 pm in reply to: Removed Thread #158290
    gegsy
    Participant

    kwatt wrote:Not guilty, but it was a bit harsh. 😉

    My moderating or the posters comment? 🙂

    Greg

    October 31, 2006 at 5:32 pm in reply to: Removed Thread #158288
    gegsy
    Participant

    Re: Removed Thread

    Ok so who deleted above 😕

    Greg

    October 31, 2006 at 5:28 pm in reply to: Bosch KGU3201 GB/01 Fridge/Freezer #193806
    gegsy
    Participant

    Re: Bosch KGU3201 GB/01 Fridge/Freezer

    Hi
    Do you have part number of PCB you have changed and original fault that led you to main PCB replacement 🙂

    Greg

    October 31, 2006 at 5:24 pm in reply to: Microwave oven #193819
    gegsy
    Participant

    Re: Microwave oven

    Hi
    Its engineer time or bite the bullet Im afraid 🙁 because due to the dangerous high voltages inside we cannot really guide you any further, sorry.
    If you should require an engineer please use the link below 🙂

    Greg

    October 31, 2006 at 5:19 pm in reply to: Neff Oven Door Broken #193397
    gegsy
    Participant

    Re: Neff Oven Door Broken

    TomDub wrote:Final question. What are the hinge bearings?, and I asssume I would need two (one each side)

    These are called so many things, the best description would be hinge receivers ie what the hinge sits and rides on and yes you would need one on each side and slight grease on each. 🙂

    Greg

    October 31, 2006 at 5:16 pm in reply to: Engineer looses finger #193628
    gegsy
    Participant

    Re: Engineer looses finger

    No heard nothing but same sentiments as Jackal.

    Greg

    October 30, 2006 at 6:02 pm in reply to: Removed Thread #158287
    gegsy
    Participant

    Re: Removed Thread

    Edited one of effzedarr post from in here http://www.ukwhitegoods.co.uk/modules.p … 168#106168

    At least he didn’t lose his finger in the customer 😆 😉
    Chris..

    That was the original post.

    Was a bit risque 😕

    Greg

    October 30, 2006 at 5:47 pm in reply to: wpl td fan change #193748
    gegsy
    Participant

    Re: wpl td fan change

    Hi
    It is a strip down but pretty straightforward.
    All done from the rear and drum out.
    The fan is in the (looking from the back) the l/h/s base manifold attached to motor shaft. Remove manifold cover then motor and thats basically it then.

    Greg

    PS – Check your email 😉

    October 29, 2006 at 7:55 pm in reply to: Bosch grill element part no. please #193694
    gegsy
    Participant

    Re: Bosch grill element part no. please

    Hi Allan
    I can find no trace for that appliance. It is 22 years old so the part may be obsolete 😕
    You may get lucky here though 😀
    http://www.bshappliancecare.com/bshspares.html

    Greg

    October 28, 2006 at 2:40 pm in reply to: Ariston as 100 #184016
    gegsy
    Participant

    Re: Ariston as 100

    Diy-Jim wrote:Greg, this was a solution back in nov 2005 by iandms, and you said then that you had known a timer cause lack of heating…I guess you must have forgotten.

    I guess so 😀 at least you must have found the “search” facilty though 8)

    Greg

    October 28, 2006 at 9:45 am in reply to: New Hotpoint Washing Machine in…… #193592
    gegsy
    Participant

    Re: New Hotpoint Washing Machine in……

    Aha, come to think of it there were some with moulded amongst them so looks like thats the case then Martin 😀

    Greg

    October 28, 2006 at 12:27 am in reply to: Keyboard available in various bust sizes….8O #193267
    gegsy
    Participant

    Re: Keyboard available in various bust sizes….8O

    You sure u lot aren’t endangered 😆

    October 27, 2006 at 11:58 pm in reply to: indesit D61 leak reasons … #193138
    gegsy
    Participant

    Re: indesit D61 leak reasons …

    Looks like a Lada Riva 😆
    Cheers aswell burns 😀

    Greg

    October 27, 2006 at 10:44 pm in reply to: New Hotpoint Washing Machine in…… #193589
    gegsy
    Participant

    Re: New Hotpoint Washing Machine in……

    Hi Mark
    They were f/s Wms, just bare 3 cores.

    Greg

  • Author
    Posts
Viewing 15 posts - 3,736 through 3,750 (of 6,724 total)
1 2 3 … 249 250 251 … 447 448 449