petalpop

Forum Replies Created

Viewing 15 posts - 406 through 420 (of 635 total)
  • Author
    Posts
  • in reply to: indesit w/m bearings #239355
    petalpop
    Participant

    Re: indesit w/m bearings

    cheers everyone

    in reply to: zanussi dryer #239303
    petalpop
    Participant

    Re: zanussi dryer

    that is what is confusing me
    belt fine
    heats up
    gets hot in drum
    cold air blows out hose
    i just don`t get it

    in reply to: Hoover spinner/TT belt #238273
    petalpop
    Participant

    Re: Hoover spinner/TT belt

    connect say they have the genuine one in stock 5031680388381 £1
    or pattern blt103 £1.10
    didn`t think the genuine one was available let alone cheaper than pattern but hey thats connect for you

    in reply to: hpt 30mm bearing kit #237730
    petalpop
    Participant

    Re: hpt 30mm bearing kit

    just checked and can`t find it
    when i did one i am sure i got a kit from them but no sign now 😥

    in reply to: AEG 88070 open the tap #237743
    petalpop
    Participant

    Re: AEG 88070 open the tap

    if the water board have been doing anything with the pipes i would turn off the tap to the dishwasher and undo it at the machine end and check the filter to see if it is blocked

    in reply to: hpt 30mm bearing kit #237729
    petalpop
    Participant

    Re: hpt 30mm bearing kit

    connections have one for about £10
    but then that all depends what discount your on

    in reply to: Hoover A8534-001 Washer Dryer Drum Bearing. #237636
    petalpop
    Participant

    Re: Hoover A8534-001 Washer Dryer Drum Bearing.

    philips screwdriver
    flat screwdriver
    10mm socket
    10mm spanner
    14mm spanner
    hammer and drift

    and thats about it
    good luck

    in reply to: Hoover A8534-001 Washer Dryer Drum Bearing. #237634
    petalpop
    Participant

    Re: Hoover A8534-001 Washer Dryer Drum Bearing.

    fairly easy job
    electric off
    back panel off
    about 12 10mm nuts and bolts around backplate then drum pulls out
    do this before getting bearings + tub seal to check drum
    if thats broken use the link and buy an ISE washer
    as drum v.expensive

    in reply to: wm premature bearing failures #237637
    petalpop
    Participant

    Re: wm premature bearing failures

    my workshop engineer has done about 5 in the last few months with genuine shaft and connections pattern bearings and we havent had a problem

    in reply to: You don’t need a web site or Yellow Pages to be found #237626
    petalpop
    Participant

    Re: You don’t need a web site or Yellow Pages to be found

    put my company on there and the 1st call i got from it was them trying to upgrade me to be seen easier
    just the same as yell im afraid 🙁 😥 🙁

    in reply to: neff w/machine #237560
    petalpop
    Participant

    Re: neff w/machine

    ok cheers

    in reply to: neff w/machine #237558
    petalpop
    Participant

    Re: neff w/machine

    got model now v5360x0gb
    E14 comes up on wash so could it be the dryer ntc???????????

    in reply to: neff w/machine #237557
    petalpop
    Participant

    Re: neff w/machine

    aaaaahhhhhh
    that makes sense 😳 😳 😳 😳

    in reply to: neff w/machine #237555
    petalpop
    Participant

    Re: neff w/machine

    i will check the ntc
    but what is IIRC

    in reply to: Beko WMA620W #237420
    petalpop
    Participant

    Re: Beko WMA620W

    connections in stock £54 pt no/5031688181120

Viewing 15 posts - 406 through 420 (of 635 total)