quassy

Forum Replies Created

Viewing 12 posts - 1 through 12 (of 12 total)
  • Author
    Posts
  • in reply to: Zannussi ZWD1261 Washer Dryer #233184
    quassy
    Participant

    Re: Zannussi ZWD1261 Washer Dryer

    Hi Sheer1delight,

    there are times when help is not forth coming – so the only solution is to cut your losses and start a fresh with a new machine.

    After all it’s only a washing machine and I paid almost as much for games console this year for my son.

    Regards,

    Quassy

    in reply to: Zannussi ZWD1261 Washer Dryer #233182
    quassy
    Participant

    Re: Zannussi ZWD1261 Washer Dryer

    🙁 Ah well, I suppose there is nothing else to do but buy a new washing machine!

    Quassy

    in reply to: Zannussi ZWD1261 Washer Dryer #233181
    quassy
    Participant

    Re: Zannussi ZWD1261 Washer Dryer

    Hi, is there anyone there?

    Do I need a new controller?

    Quassy

    in reply to: Zannussi ZWD1261 Washer Dryer #233180
    quassy
    Participant

    Re: Zannussi ZWD1261 Washer Dryer

    Got the part, the old one looked the same as the new one – fitted it any way – same problem. Any more ideas?

    Regards,

    Quassy

    in reply to: Zannussi ZWD1261 Washer Dryer #233178
    quassy
    Participant

    Re: Zannussi ZWD1261 Washer Dryer

    HI Martin,

    Just out of interest, looking @ the serial number, what would you say was the year of manufacture?

    Thanks again for all your help, I’ll order the part today.

    in reply to: Zannussi ZWD1261 Washer Dryer #233176
    quassy
    Participant

    Re: Zannussi ZWD1261 Washer Dryer

    Thank you for the information.

    Would a spare ‘drive pawl’ be ready avable for this machine?

    Many thanks

    in reply to: Powerpoint Washer Dryer #181088
    quassy
    Participant

    Re: Powerpoint Washer Dryer

    Hi Dave,

    The machine seams to be operating OK.

    I did check the filter, it was clean. The machine is only operated twice from new.

    Is the machine made in China?

    in reply to: Powerpoint Washer Dryer #181086
    quassy
    Participant

    Re: Powerpoint Washer Dryer

    It is the 1200IWD

    in reply to: Ariston Dishwasher #176854
    quassy
    Participant

    Re: Ariston Dishwasher

    Hi again,

    I checked out the water pressure to the machine and “Float Switch” and both check out OK. No sign of water leaking in the machine.

    I put water into the machine and started it running. A pump starts.
    I opened the door and found the water I put in has gone.

    After a while, there is the sound of water running.

    About 1 1/2 minutes after starting the machine, a pump starts again and the same light that is second from the left starts flashing.
    This sound of pump and water runs last about thirty seconds and then all gose quiet.

    in reply to: Ariston Dishwasher #176852
    quassy
    Participant

    Re: Ariston Dishwasher

    Hi Dave & Greg,

    Thanks for the information.

    I’m sure the water supply is OK.

    There is a dry residue lying on the inside bottom of the machine.
    So it looks like a leak I’m looking for!

    Where would the device for the “flood protection activated” be located and what would it look like.

    Another thought, where I could get a wiring diagram/manual.

    Many thanks

    Quassy

    in reply to: Ariston Dishwasher #176850
    quassy
    Participant

    Re: Ariston Dishwasher

    Model LI62
    Type # LS 12-BIT100
    S/N 207012541

    in reply to: Ariston Dishwasher #176847
    quassy
    Participant

    Re: Ariston Dishwasher

    Hi iadom,

    the button that is flashing is the second from the left hand side of the machine. There are four (4) buttons in all on the left. I started the wash cycle by de-pressing the first button on the left (symbol with a pot with under lines). The door is closed. It sounds like a pump is running. After a while nothing else seams to be happening. On re-opening the door the button with a pot like symbol is flashing.

Viewing 12 posts - 1 through 12 (of 12 total)