Forum Replies Created
-
Posts
-
Re: Fisher & Paykel GW701 Fills & Drains
hi,try blowning hard down the pressure tube on the side of the bowl .turn off power dissconnect from top.
Re: f&p MW051-U won’t fill….pressure sensor fault?
hi,just a thought does it fill up if u select hot water and also does it stop at low level if u select low level with hot water..if so id say its your cold water valve.
Re: Fisher&Paykel Smartdrive 058 controller board help?
what is it doing ,when u say it playing up again
hi silvercody here,if the fault code 9 is coming up it means the size is wrong….push & hold wash temp down then together push the power button all lights will come up then push the spin button so that the green light is hold then push power button..
silvercody here ,iam not sure what u mean ,do u mean the other one as your old one or the new one ,,also iam not sure if putting a yellow display panel into a green motor controller would work iam sure that they have to be the same colour.
Re: Error code 9 on SmartDrive 703
hi silvercody here,thats ok if its a green one ,but as u might know so techs r lazy and dont use the right parts, they use other ones that will work aswell,so 703 sometimes does mean nothing.. if its a green one to set the size is different as a yellow so i was only asking what colour it was so that the right info is giving..as for that funtion i told him..in the f & p handbook it says when replacing a motor controller or touch panel u must push and hold the start button then together push power button for it to reset…anyway was just trying to help , because this is easy for him to do with out spend any $$$$
hi silvercody here, i tip just try this,with it on at the wall but off on the machine try push & hold start button and together push power button a couple of lights sould come up wait 20 seconds then push power button..also what colour is the touch panel & is it a gw
Re: Fisher&Paykel Smartdrive 058 controller board help?
HI SILVERCODY HERE,JUST THOUGHT I WOULD TELL U THAT I FIXED A MACHINE TODAY THAT WAS DOING THE SAME THING I THINK,VAVLES R PUSLES AND ALSO WHEN DRAINING IT STOPS AND STARTS,I REPLACED HOT AND COLD VAVLES AND NOW IT WORKS FINE..I DONT KNOW WHICH ONE MIGHT HAVE BEEN BAD BUT IT WORKS NOW..JUST THOUGHT I’D TELL U..
Re: Fisher&Paykel Smartdrive 058 controller board help?
hi silvercody here,u need to post us the fault code that is coming up..if the machine is on & off when filling thats most of the time the obb swicth under your motor controller if replaced just make sure thats u have the yellow wire on the side of it not on the end of it, an other one is rps swicth under the machine that is on the the stator which i think u said u replaced be careful putting that back in it can break easy and make sure it is in there properly also make sure that the other wires next to it r in the right order ( from left to right yellow,blue ,red).the other is the motor controller,but u said that u just replaced it. after finishing any thing that u have replaced i always push on hold start then together push power wait 20 seconds then push power button again.. but the fault code we need..
Re: fisher & paykel when agitator hit the sides
have just repaced some sus rods has a new spring but still doing it is ther any thing more ,..could it be the obb swicth..
Re: Fisher&Paykel Smartdrive 058 controller board help?
hi silvercody here,the only two things that i can think of is might be the clear pressure tube & the liitle blue tube connected to the bowl might be bent from where it comes up from the top deck and connects to the motor controller, disconect it from the top and blow throught it to clear any thing.the second might be the oob swicth or micro swicth which is under the motor controller it might be worn out,make sure that the yellow wire pluged on the side of it & not at the end of it..that swicth can be tested by pushing that program i told u wash temp down ….ect……..when in the program stick your arm under the top deck and push back the little lever if a light comes on up where your advance lights r it means its works..
Re: Fisher&Paykel Smartdrive 058 controller board help?
hi silvercody here,i think thats a motor out of sequence..try turning the machine off at the wall for 30 seconds & then back on at the wall then push and hold start button and together push power button,some fuctions sould come up just wait 30 seconds and then push power button again..also if this is a new motor controller u just put in u might have to set the size..if its a yellow motor controller push & hold down wash temp down & together push power button,all light will come on for a couple of seconds and then u can set the size …if its a( 5kg push the wash temp down button,)if its a (6kg push the low button) & if its ( 7kg push the hold button) the button r right beside each other..
Re: Fisher&Paykel Smartdrive 058 controller board help?
hi sivercody here ,its just a tip but when replacing a motor controller u have to activate it by holding down start button then push power button then wait 10 seconds and push power again..also there is a little button under the console if u take the lid off by lifting it up..your’ll see it on the right hand side under the console if your lid doesn’t push that button in when u close the lid it wont work it will just beep when u push the start button,..start the machine up normally with the lid off and push the button in with your finger if it starts that means your lid is’nt pushing that button it.if it dosnt it might mean your obb swicht might be shot.. just try the first bit first..hope it works for u..by the way is the motor controller blue..
.
