Forum Replies Created
-
Posts
-
Re: Bosch Tumble Dryer Cuts off (presumably it’s too hot)
Hi Don, Martin
I changed the NTC Thermistor at the front of the machine but unfortunately the tumble dryer exhibits the same exact symptoms! is there another temperature thermistor/thermostat that I should try to change also? (at the back somewhere)?
Thanks
ChrisRe: Bosch Tumble Dryer Cuts off (presumably it’s too hot)
Thanks Martin, Don, I have ordered a replacement part from your shop’s website.
I am pleased to learn that I can replace this thermistor easily from the front; as I have never taken the tumble dryer apart before, any guidance of how to remove the front panel, and where to locate the suspect thermistor (before I start dismantling things!).
THANK YOU again for helping me.
Best regards
ChrisRe: Bosch Tumble Dryer Cuts off (presumably it’s too hot)
Thank you Martin – that was such a quick response!
Can you recommend where to purchase a replacement Thermistor, and any guidance in how easy it is to access & replace it? [I have some difficulty tracing much on the internet by searching for ‘Bosch Logixx WTS86516GB’, I wonder if it is known by some other name].
Yes – the machine has been cleaned regularly (from the front), i.e. removing debris (at the bottom of the loading door) & keeping the condenser clean (bottom left hand side).
I assume I can get access to replace this thermistor once I remove the back panel?Thank you so much again Martin – Chris
Re: WMD960 – F01 etc
THANKS iadom – all makes sense and will follow your recommend.
I assume EMW means http://www.emwelec.co.uk ?
One final query if I may: any special advice in removing the PCB? Is it straight forward – just unplug cables and remove screws? Any particular tip?
Thank you again!
Re: WMD960 – F01 etc
Hi Washman
Thank you for a very prompt response; however I am not sure it answers all my questions:
“Can you please provide any advise on (i) how to take the PCB out, and (ii) where best to purchase a replacement. Any concerns in using a refurbished PCB?
(finally! if I have to remove the motor again to get to the PCB do you have a trick for putting the belt back on again! I struggled doing this last night)”.
Thanks again – I am not very experienced in using these forums, but I greatly appreciate your support.
Re: WMD960 – F01 etc
Very useful reply; my washing machine has a similar (f01) fault.
No obvious marks inside the machine and wiring all seems OK. Not knowing the motor is brushless (should have checked here!) I took the motor off, but now I put all back.
Can you please provide any advise on (i) how to take out the PCB out, and (ii) where best to purchase a replacement. Any concerns in using a refurbished PCB?
(finally! if I have to remove the motor again to get to the PCB do you have a trick for putting the belt back on again! I struggled doing this last night).
THANK YOU!!!
Re: Zanussi Jet System 1300 XC User Manual urgently required
Hi Don
Yes, I now have the machine’s details:
Product Number: 91460141401
Type: P6348670
Model: WJD1357S
I hope these are the descriptions you were after. Again – THANK YOU!
Chris
Re: Zanussi Jet System 1300 XC User Manual urgently required
Thanks Don – your response was very impressive. I shall check the machine tonight and let you know tonight. Perfect – thank you!
Re: What is F27 on a Bosch Logixx8 WAS32466GB/05 washing mac
Hi Martin, Kwatt – MANY MANY THANKS to both for taking the trouble and time to reply to my request for help!
So, F27 suggests a fault with the Analogue Pressure Switch Part Number 619600. Can I ask one last big favour please – where do you suggest I buy a new component, and how easy is it to replace the old one (briefly – how do I get access to it and any special instructions to remove/replace it)?
Thank you very much again. I am happy to buy a new one and replace the old one provided you think it is reasonably straight forward.
Indebted!
Chris
