yorkshireracer

Forum Replies Created

Viewing 11 posts - 31 through 41 (of 41 total)
1 2 3
  • Author
    Posts
  • April 22, 2010 at 11:26 am in reply to: CPCA240FSK temp probe #316785
    yorkshireracer
    Participant

    Re: CPCA240FSK temp probe

    I’ve measured the spot mentioned, but no probe. Any ideas??

    March 17, 2010 at 1:23 pm in reply to: Hoover Dishwasher HED6612 #305100
    yorkshireracer
    Participant

    Re: Hoover Dishwasher HED6612

    I have a machine with the same fault. According to hoover they say it does not have a flow meter. They say the cause of this fault code is a water softner capacitor, part # 49011670. Any ideas??

    October 13, 2009 at 11:19 am in reply to: whirlpool awm5104/5 washing machine #299136
    yorkshireracer
    Participant

    Re: whirlpool awm5104/5 washing machine

    Many thanks, worn brushes replaced, machine working.

    August 24, 2009 at 9:08 am in reply to: Hotpoint FF175 dead #294666
    yorkshireracer
    Participant

    Re: Hotpoint FF175 dead

    seriel number is 701113034

    Thanks in advance.

    May 30, 2009 at 10:36 am in reply to: Connect Prices #288085
    yorkshireracer
    Participant

    Re: Connect Prices

    Stand corrected, 2 modules listed one at 30 odd one at 60 odd.

    May 30, 2009 at 10:33 am in reply to: Connect Prices #288084
    yorkshireracer
    Participant

    Re: Connect Prices

    £68.56 to me and I spend about £35k a year with them. Phone call to rep on monday…………………………………………………

    May 28, 2009 at 11:32 am in reply to: ABA8152 diplomat/sevis/baumatic witring diagram #287567
    yorkshireracer
    Participant

    Re: ABA8152 diplomat/sevis/baumatic witring diagram

    The wire colours don’t quite match up. I have 2 thiner grey wires,so have connected to the silver coloured terminals on stat. That leaves me with one think grey link wire which I have conected between the thermostat and element, one thick red which I have connected to stat and one thick black which I have connected to element.

    Wiring this way the machine completes a program but does not heat. Is this wired correctly and if so is it likely to be the module?

    May 28, 2009 at 11:24 am in reply to: AEG W/dryer L16810 #287371
    yorkshireracer
    Participant

    Re: AEG W/dryer L16810

    Not quite so simple……………………………..

    Left the machine and all seemed to be fine. Got a call today, no heat in the dryer again and also a couple of the option buttons/lights will not opperate. Are we looking a t a board/pair of boards?

    May 22, 2009 at 11:34 am in reply to: AEG W/dryer L16810 #287370
    yorkshireracer
    Participant

    Re: AEG W/dryer L16810

    Many thanks, have returned this morning. Thermistor ok, tightened all edge connectors on main module, bingo!!!

    Cheers

    May 16, 2007 at 7:47 am in reply to: Indesit SGE12XUK Int W/Machine Electronic Fault?? #213826
    yorkshireracer
    Participant

    Re: Indesit SGE12XUK Int W/Machine Electronic Fault??

    Brushes have plenty left on them and are equal in length!

    Thanks anyway.

    November 25, 2006 at 4:16 pm in reply to: Creda 48143 gainsbourough wiring diagram #196344
    yorkshireracer
    Participant

    Re: Creda 48143 gainsbourough wiring diagram

    Thanks, but some how I have managed to loose the wire to S2 whilst converting from strix to diamond. Having a mental block!!

  • Author
    Posts
Viewing 11 posts - 31 through 41 (of 41 total)
1 2 3