This set of fault codes for the AW23 washing machine model only from ISE and may not relate to any other models.
These error codes do not relate to ALL ISE washing machines. If you are unsure please ask in the forums as well as for all other ISE washing machine fault codes.
Before you start any investigation of the fault or even remove the lid of your washing machine please read and fully understand this article in full and pay particular attention to the safety and information notices at the bottom of this page as they contain extremely important information!
Please remember to support our site by buying washing machine spares from our spare part store and, if you decide that you need a washing machine engineer please support the local repairers that help make this site possible, you can search for a local washing machine repairer using our engineer search.
ISE AW23 Washing Machine Fault Codes
These fault codes are written for washing machine repairers and not for the general public by ISE and they assume a certain level of competence on the part of the user in diagnostic routines. We have added some notes to try to assist you in determining the nature of the fault you have but, you will still need to investigate each failure on its own merits. For more help and advice on fault finding on a washing machine please refer to our washing machine fault finding guide from this link before you begin.
If you struggle or cannot find the appropriate fault code that you need for your washing machine please ask in the forums and the gusy there will do what they can to help and locate the meaning of the fault code you need
ISE Washing Machine Spares
We have purposely not listed any ISE washing machine spares in this article.
Please, don’t guess or assume as spares can be altered on a production run with the same model number having several different alternative components used.
|
P** |
Display shows P followed by two digits. The two digits can be any numeric value that corresponds to a program number. This is not a fault.
The program dial has been moved while the machine was in operation. The program will complete as normal but the display may still be displayed and the machine not able to select a new program. Press and hold the start/reset until the error clears, restart program. |
|
E01 |
No feedback signal from the washing machine door lockAfter 15 seconds, the E01 code is shown and the washing programme is stopped. Open or close door of the washing machine
|
|
E02 |
Fill timeout, filling takes more than two minutesAfter washing ends, the E02 error is shown. Additional water taking is blocked above the pressure control level.
|
|
E03 |
Failure to drain, the washing machine takes more than one and a half minutes to drain downThe next spinning after pumping out is limited to 400 rpm, after the programme ends the E03 code is shown.
|
|
E04 |
The washing machine pressure control sends an “overflowing” signal – Overfill detectedThe programme is stopped, the pump is switched on and the E04 code is shown. 1.5 minutes after the “empty” signal from the pressure control, the pump is switched off. If water is detected once again when E04 is shown, the pump is switched on again.
|
|
E05 |
Fill level not reached ten minutes after fill beginsThe programme is stopped and the E05 code is shown.
|
|
E06 |
The washing machine does not detect that the machine has drained after ten minutesThe programme is stopped and the E06 code is shown.
|
|
E07 |
Not used on the AW23 washing machineLeak detected where sensor is fitted, not used on the AW23
|
|
E09 |
Too much foam detected in the washing machineThe programme ends without spinning with the error code displayed
|
|
E11 |
No detection of the triac for the door lockAfter 2 seconds the E11 code is shown and the washing programme is stopped.
|
|
E21 |
Failure to read washing machine motor tachoThe programme is stopped and the E21 error code is shown.
|
|
E22 |
Short circuit on the washing machine motor triacThere is a signal from the tachogenerator although
|
|
E31 |
Temperature sensor shortedThe programme is not stopped. After the washing ends, the E31 error is shown.
|
|
E32 |
Temperature sensor is open circuitThe programme is not stopped, after the washing ends, the E32 error is shown.
|
|
E34 |
Water heater not detected in circuitWashing machine will completed the cycle and end with the E34 error code displayed
|
|
E42 |
Door has not unlocked in over two minutesThe error occurs at the end of washing, if after washing ends, the door is not unlocked within 2 minutes. The E42 code is shown and does not allow another cycle to be switched on without resetting the error code.
|
|
E51 |
Incorrect data in washing machine programmer memoryDisplayed as error code, washing machine start not possible, washing machine disabled
|
|
E52 |
Incorrect data in washing machine programmer memoryDisplayed as error code, washing machine start not possible, washing machine disabled
|
|
E53 |
Input circuit EMC errorsDisplayed as error code, washing machine start not possible, washing machine disabled
|
|
E54 |
Washing machine autotest errorDisplayed as error code, washing machine start not possible, washing machine disabled The washing machine dial has been turned or options selected too quickly and the machine has not been able to process the commands or engage the options as requested. This is a common error where people press buttons repeatedly thinking that the command has not been accepted as the display has not updated instantly. In all cases simply reset the machine by holding the Start/Reset button for approximately thirty seconds and the error will clear and the washing machine will return to normal operation. |
More Washing Machine Help, Advice And Guidance
Should you need more help and guidance please use the links from this article as most of them will help you to understand your ISE washing machine a lot better and probably very much help you in diagnosing the fault you have. Of course there are many other articles on the site that will also help you do this.
In addition you can post in our washing machine forum after registering but please do pay heed to the information below before doing so and read the guides, they are there to help you.
You must understand certain things before you begin or attempt any repairs on your own and we want to make these points very, very clear to anyone that decides to investigate one of these or any other washing machines:
- We are not responsible for your safety, you are and by using this guide you accept that and accept that any damage that you may cause and work undertaken is entirely at your own risk.
- We will advise the common causes of the fault codes but we cannot guarantee that any parts or work recommended will resolve the issue. It is entirely your responsibility to diagnose your particular problem and resolve it.
- We are not responsible for you buying spares that do not resolve the problem, this is down to your own diagnosis not ours.
- No warranty is inferred, implied or given.
You also have to understand that fault or error codes are not a “magic bullet”, they will not tell you what the problem is, they will only offer you an indication of where the problem lies and they are no substitute for good old fashioned diagnostic skills. You can find out more about what fault codes actually tell you in this article. So please be well aware that, even with this new found knowledge you will still have to actually be capable of investigating and diagnosing the problem and this means adhering to basic appliance safety for working on them.
Please do note that manufacturers can and do change fault codes without notice and we cannot guarantee that these error codes will apply to your particular model as all codes apply to a wide range of appliances and not normally any one specific model.
Can you please advise what code e35 isThank you