Alanj

Forum Replies Created

Viewing 15 posts - 376 through 390 (of 757 total)
1 2 3 … 25 26 27 … 49 50 51
  • Author
    Posts
  • July 29, 2009 at 5:53 pm in reply to: 3RLSQ8000JQ2 toploader not spining properly #293384
    Alanj
    Participant

    Re: 3RLSQ8000JQ2 toploader not spining properly

    Hi IP
    it,s probably the drive coupling. Tip machine back enough for you to get under at front, disconnect pump from motor(spring clip), and then motor from gearbox(2 screws). On the end of the motor you will find a rubber drive type thing with 2 white plastic pieces with three fingers, which interlock through the rubber drive. usually one or both of the plastic pieces are broken. Part number 481932528035 @ £9.08 +vat from Connect or £10.88 +vat from Masterpart.
    Hope this helps
    Alan

    July 23, 2009 at 10:45 am in reply to: Whirlpool 3LSC8255EQ1 #292900
    Alanj
    Participant

    Re: Whirlpool 3LSC8255EQ1

    Hi Guys,
    thanks for all your help, I did find the bolt under soapy white water 😳 . Must have been one of those days 8O.

    Alan

    July 22, 2009 at 10:28 pm in reply to: Whirlpool 3LSC8255EQ1 #292899
    Alanj
    Participant

    Re: Whirlpool 3LSC8255EQ1

    I’ve sent roly16 & bzz67 a sketch of what I can see looking from above agitator for more info. Please check your e-mails

    Alan

    July 22, 2009 at 9:23 pm in reply to: Whirlpool 3LSC8255EQ1 #292896
    Alanj
    Participant

    Re: Whirlpool 3LSC8255EQ1

    I have lifted out detergent cap, and then clear plastic cover with wings which has a rubber o ring around it but no sign of a bolt head.

    Alan

    July 22, 2009 at 12:31 pm in reply to: Smeg FA550X #292391
    Alanj
    Participant

    Re: Smeg FA550X

    Thanks for the reply mark, appliance is out of warranty. But was advised by Smeg that back board was most likely cause. It wasn’t, so that’s why I asked the question here. Smeg tech also inferred that ice could be down to defrost stats.

    Alan

    July 21, 2009 at 9:27 pm in reply to: Smeg FA550X #292389
    Alanj
    Participant

    Re: Smeg FA550X

    Anyone not on holiday?

    July 21, 2009 at 9:25 pm in reply to: indesit wie 167 #292542
    Alanj
    Participant

    Re: indesit wie 167

    Have you checked the motor brushes, heater wiring, pump ❓ 💡

    Alan

    July 21, 2009 at 9:21 pm in reply to: delonghi dfs901ss wiring diagram #292780
    Alanj
    Participant

    Re: delonghi dfs901ss wiring diagram

    Hi Paul,
    you have mail. 😉

    Alan

    July 21, 2009 at 8:31 pm in reply to: Whirlpool AWM6145/3 #292857
    Alanj
    Participant

    Re: Whirlpool AWM6145/3

    Hi JJ,
    I would start with the brushes too. 🙂

    Alan

    July 21, 2009 at 6:48 pm in reply to: Zanussi Welded Tub #292755
    Alanj
    Participant

    Re: Zanussi Welded Tub

    Hi Phil,
    if the foreign object is magnetic, a large magnet (like the large circular one out of a tv ) inside the drum and turn slowly till magnet is at 12 o’clock then release magnet and catch stuck item.

    Alan

    July 21, 2009 at 6:14 pm in reply to: Smeg UK80MFX 1 #292810
    Alanj
    Participant

    Re: Smeg UK80MFX 1

    You have mail, I hope it helps.
    Alan 🙂
    And some more mail.

    July 21, 2009 at 5:13 pm in reply to: Smeg UK80MFX 1 #292808
    Alanj
    Participant

    Re: Smeg UK80MFX 1

    Sorry rocker, there is an updated delay stat. You can get technical info from Smeg.

    Alan

    July 21, 2009 at 4:28 pm in reply to: Smeg UK80MFX 1 #292807
    Alanj
    Participant

    Re: Smeg UK80MFX 1

    Should be part no 818731011.

    Alan

    July 17, 2009 at 4:31 pm in reply to: akz145 oven #290775
    Alanj
    Participant

    Re: akz145 oven

    Hi snig,
    send me an e-mail address and i’ll sort you out.

    Alan

    July 17, 2009 at 4:28 pm in reply to: Schreiber APM6855 #292392
    Alanj
    Participant

    Re: Schreiber APM6855

    Anyone?

  • Author
    Posts
Viewing 15 posts - 376 through 390 (of 757 total)
1 2 3 … 25 26 27 … 49 50 51