[Alanj]

Re: Beko WM612W

Thanks Seamy, will check that out.

[Alanj]

Re: Beko WM612w

Did you solve this problem Ray?

[Alanj]

Re: AEG oven 944185765 01

Hi Martin, would have been good to see what pages 68 & 69 say about error? 😉

[Alanj]

Re: Miele G646-3 SC Plus

Check the circulation pump for debris like biscuit wrappers or plastic that has got past filter.

[Alanj]

Re: Rangemaster 90 (6432 150165) Ceramic Hob

Hi Jonty, I would check the limiter on the hob/element. I had one recently that caused the same problem.

Alan

[Alanj]

Re: Zanussi ZWI70201WA. PN 914528134/00

Turns out the machine is under a 2 year warranty so Zanussi called out.

Thanks

[Alanj]

Re: Samsung oven BF641FSTP -SE- error

http://knowhow.com/article.dhtml?articleReference=3351&

Googled this if it helps?

[Alanj]

Re: Bosch DW Check Water

Hi Dave, possible reed switch flow meter problem? Have you checked for blockages between sump and metering tank? Is the air break on metering tank clear of gunk.

Alan

[Alanj]

Re: Whirlpool Akp206/ix

Hi clockworkone, this might help.

Alan

[Alanj]

Re: Zanussi ZWI70201WA. PN 914528134/00

Cheers Dave will take a look.

[Alanj]

Re: Neff S51E50X1GB/13

Did you get this sorted reaper?

[Alanj]

Re: bosch waa24171gb/12

This might help too

siemens-iq300-reset-procedure-t93049.html#p445253

[Alanj]

Re: Miele Dishwasher F84 error

I’ve done a couple of these where there was plastic wrappers blocking them. Most likely scenario.

Alan

[Alanj]

Re: BEKO DRYER DCX83100W

Probably heater unit. Heating element can be ok but ntc/thermistor goes faulty. Complete unit required unfortunately 🙁

[Alanj]

Re: Siemens iq300 reset procedure

Hi, found this after a search. Might be of help.

After fitting new brushes to a Bosch or Siemens washing machine you may be dismayed to find that it still doesn’t work.

Don’t Panic!

One of the following Reset procedures, depending on the model you have, will probably get the machine going again.
==============================================================================
Reset Procedure 1, for a Siemens 16S series (WM16S) series machine after F43 error / Nulstilling af Siemens vaskemaskine efter F43 fejl (Thanks to https://madsdyd.wordpress.com/2014/12/0 … -f43-fejl/ )
Turn off the machine (dial to 0)
Open the door
Turn on the machine on first program
Close the door
Turn off the machine
Turn on the machine on the “six-o-clock” program, which is centrifuge
Press the “option down” button and keep it pressed (This is the button left of the display)
Turn the dial to “seven-o-clock” (empty/pump out program)
Release the “option down” button
Turn of the machine
================================================================================
Reset Procedure 2 (most commonly seen online, but not applicable to all machines)

Turn the knob to off.
Close the door.
Turn the knob to 6 o’clock position.
Wait 2 seconds.
The start/pause should begin flashing.
(If the start button doesn’t flash, just carry on trying to erase the codes).
Press and hold the spin button. (it may be marked RPM)
Turn the knob to 7 o’clock position.
Wait 2 seconds.
Release the button.
Turn the knob to off.
========================================================================================================================================================
Reset Procedure 3 for Bosch Maxx Classic washing machine
1. Close the door and make sure the dial is in the OFF position.
2. Hold the Start/Pause button and turn the dial anti clockwise (to the left) to the express 15 min program at the same time.
3. Hold the Start/Pause button for 10 seconds sometimes more.
4. Release the button and turn the dial back to the OFF position.
5. Select any program and the error should not be appearing.

Alan

[Author]

Posts