eng14

Forum Replies Created

Viewing 15 posts - 166 through 180 (of 201 total)
1 2 3 … 11 12 13 14
  • Author
    Posts
  • December 4, 2010 at 4:25 pm in reply to: Cannon C60ETC #337889
    eng14
    Participant

    Re: Cannon C60ETC

    Martin,no only the far right hand main oven/selector switch and u/s clock,richard 😕

    November 8, 2010 at 7:41 am in reply to: bosch wfl 2067gb/01 #335180
    eng14
    Participant

    Re: bosch wfl 2067gb/01

    thanks guys ill check those carbons again,no it wont agitate,richard 😉

    October 18, 2010 at 4:23 pm in reply to: bosch sgs8812gb/35 #333141
    eng14
    Participant

    Re: bosch sgs8812gb/35

    martin the machine is fine when configured out of facia,put the silly thing back in and its wrong,you were right the times are perfect out of facia,richard, 🙁

    October 18, 2010 at 4:18 pm in reply to: electrolux 914602300-00 wd #333109
    eng14
    Participant

    Re: electrolux 914602300-00 wd

    mike the description from them is vague as usual,i have not been yet but i think you are spot on the same thing here.circulating pump eh,its given me a start point many thanks richard, 🙂

    October 17, 2010 at 5:16 pm in reply to: bosch sgs8812gb/35 #333140
    eng14
    Participant

    Re: bosch sgs8812gb/35

    thankyou very much martin,ill reset out of facia on 2 reset buttons and start again richard, 😀

    October 17, 2010 at 3:05 pm in reply to: bosch sgs8812gb/35 #333138
    eng14
    Participant

    Re: bosch sgs8812gb/35

    martin sorry yes we did try with code u sent found some of my old ones as well.no this mc will not play ball,all progs are fine except quick wash which will not come down from 145 mins.thats why i put it back on the site,watch this space 😳

    October 16, 2010 at 3:28 pm in reply to: electrolux 914602300-00 wd #333107
    eng14
    Participant

    Re: electrolux 914602300-00 wd

    i will give it a try seamy,ta 🙂

    October 12, 2010 at 5:48 pm in reply to: bosch sgs 8812gb/35 #332660
    eng14
    Participant

    Re: bosch sgs 8812gb/35

    thanks martin they left out the coding sheet,i wondered where it was thinking they now need bosch to configure.rang bosch, they said error to leave out just my luck,richard. 😀

    September 1, 2010 at 4:50 pm in reply to: zanussi t/d #328764
    eng14
    Participant

    Re: zanussi t/d tce 7227w

    i have just found one with the same/similar fault.it pumps then drum action for 5 seconds then beeps end,thanks richard. 😕

    August 22, 2010 at 8:26 am in reply to: Lg wm12336fd #328029
    eng14
    Participant

    Re: Lg wm12336fd

    yes this has two pumps,attached to the filter housing.

    June 2, 2010 at 8:37 am in reply to: Smeg Range Cooker AI.I 2FA #320875
    eng14
    Participant

    Re: Smeg Range Cooker AI.I 2FA

    thanks clive the cut out on this one is in the back top right,it seems you cant get this 4 wire stat any more it is 2 wire.i presume its 2 wires per per contact,where can i buy and part no,thanks guys,richard. 😕

    May 14, 2010 at 7:50 am in reply to: hotpoint wd 640 #320270
    eng14
    Participant

    Re: hotpoint wd 640

    yes changed wash heater,dryer stat,ntc,new card showing f07,richard. 😕

    September 25, 2009 at 7:47 am in reply to: arrow foghss #297878
    eng14
    Participant

    Re: arrow foghss

    thanks chris its teb01,richard 😀

    January 29, 2009 at 6:46 pm in reply to: HOTPOINT COOKER HINGES #275620
    eng14
    Participant

    Re: HOTPOINT COOKER HINGES

    thanks guy’s for your help richard. 🙂

    January 29, 2009 at 6:44 pm in reply to: AEG T/DRYER #275617
    eng14
    Participant

    Re: AEG T/DRYER

    thanks martin ,yes done that still no joy,richard. 😕

  • Author
    Posts
Viewing 15 posts - 166 through 180 (of 201 total)
1 2 3 … 11 12 13 14