gav425

Forum Replies Created

Viewing 11 posts - 1 through 11 (of 11 total)
  • Author
    Posts
  • May 7, 2012 at 6:56 pm in reply to: SEBO X4 Extra Which? report #360563
    gav425
    Participant

    Re: SEBO X4 Extra Which? report

    Just home with my new Sebo X4. Had a Dyson animal, so did the vacuum with that first. Now just had a go on the Sebo, what a different class. So much less noise and a much better pick up, carpet looking good, very pleased. 😀

    April 25, 2012 at 3:09 pm in reply to: Bosh SGS66A02GB/17 Problem #373622
    gav425
    Participant

    Re: Bosh SGS66A02GB/17 Problem

    You were right about QER, they cannot fix the board, so I’ll be needing a new one. 🙁

    April 24, 2012 at 12:50 pm in reply to: Bosh SGS66A02GB/17 Problem #373620
    gav425
    Participant

    Re: Bosh SGS66A02GB/17 Problem

    Trying to trace the tracks on the board it seems to follow back to the rinse aid sensor.

    No, I’m not trade. Just the family fix it, make do and mend guy.

    April 24, 2012 at 10:52 am in reply to: Bosh SGS66A02GB/17 Problem #373618
    gav425
    Participant

    Re: Bosh SGS66A02GB/17 Problem

    Have checked heater element and got 24ohms so this shouldn’t be the cause of this blow. Any other checks before I send control module to QER? Thanks for any help.

    April 24, 2012 at 10:11 am in reply to: Bosh SGS66A02GB/17 Problem #373617
    gav425
    Participant

    Re: Bosh SGS66A02GB/17 Problem

    Blown control module is what I have found. 👿 Is it just a straight swap for a new one or will this have blown for another reason?


    👿 👿 👿


    Mod edit:

    Attached your picture using the board upload function.
    Don

    April 22, 2012 at 4:42 pm in reply to: Bosh SGS66A02GB/17 Problem #373616
    gav425
    Participant

    Re: Bosh SGS66A02GB/17 Problem

    All the pipes have been off and cleaned, 1st thing I did. Thanks anyway!

    October 6, 2010 at 4:36 pm in reply to: Bosch SGS66A02GB/17 Prog times extend #331961
    gav425
    Participant

    Re: Bosch SGS66A02GB/17 Prog times extend

    Has now done 1 run empty and 1 full load all looks to be in good working order.
    Thank you uk whitegoods!

    October 5, 2010 at 1:27 pm in reply to: Bosch SGS66A02GB/17 Prog times extend #331960
    gav425
    Participant

    Re: Bosch SGS66A02GB/17 Prog times extend

    Have today done a strip and clean of the bottom dirty hose and the big and smaller side chambers. just switched on for a programme run so will report back how we get on.

    October 4, 2010 at 7:53 pm in reply to: Bosch SGS66A02GB/17 Prog times extend #331959
    gav425
    Participant

    Re: Bosch SGS66A02GB/17 Prog times extend

    ok looks like it has the 1min to go problem so tomorrow its strip and clean all hoses.

    June 21, 2008 at 1:44 pm in reply to: Hoover HNWL6136 Only 1 programme #255507
    gav425
    Participant

    Re: Hoover HNWL6136 Only 1 programme

    thank you. I have had a look at the filter with the drain pump and the little propeller is not spinning so its not emptying.

    Thankyou for your help.
    gav425

    June 4, 2007 at 12:27 pm in reply to: in-line heater test? #170442
    gav425
    Participant

    Re: in-line heater test?

    Thanks to this thread I have just repaired my AEG 40640. It was not heating up and had the same dry joint on the PCB inside the door.
    Thank you very much.
    gav425

  • Author
    Posts
Viewing 11 posts - 1 through 11 (of 11 total)