gramp

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 29 total)
1 2
  • Author
    Posts
  • August 6, 2015 at 1:08 pm in reply to: Neff S5555X0GB/56 part no. required #429451
    gramp
    Participant

    Re: Neff S5555X0GB/56 part no. required

    thanks but have now found the part that is required it is part of the facia .
    thanks for looking Alex .

    August 5, 2015 at 4:07 pm in reply to: Neff S5555X0GB/56 part no. required #429450
    gramp
    Participant

    Re: Neff S5555X0GB/56 part no. required

    its the black plastic bit that the module box clips into so that the controls stick up into the facia

    March 11, 2015 at 1:51 pm in reply to: Bosch wae24166gb/06 #425466
    gramp
    Participant

    Re: Bosch wae24166gb/06

    yes checked all the usual suspects. going to try it again over the weekend when we have more time to sit and watch it .
    thanks to all who have looked .

    February 2, 2015 at 3:33 pm in reply to: Maytag mwa10149wh F26 fault #424326
    gramp
    Participant

    Re: Maytag mwa10149wh F26 fault

    thanks for your help . will have a look at that .

    Alex.

    January 3, 2015 at 11:21 am in reply to: lg ice maker #423156
    gramp
    Participant

    Re: lg ice maker

    Thanks for looking panic over as it is working again now .Just gave everything a clean again .

    October 9, 2014 at 9:20 am in reply to: Whirlpool AFB823 door seal #419643
    gramp
    Participant

    Re: Whirlpool AFB823 door seal

    Got the right seal sorted out it was the same as the fridge model ARG582 part no 480132100607 thanks to everyone who looked but now resolved .

    September 30, 2014 at 11:32 am in reply to: zwd12270w1 not condensing #419609
    gramp
    Participant

    Re: zwd12270w1 not condensing

    Martin i checked the heater and it was fine so replaced the dryer module and that seems to have cured the problem. Thanks for your help.

    September 25, 2014 at 5:36 pm in reply to: zwd12270w1 not condensing #419608
    gramp
    Participant

    Re: zwd12270w1 not condensing

    Martin . Will check that tomorrow was going to try changing the dryer module too and see how it goes from there

    September 24, 2014 at 8:17 pm in reply to: zwd12270w1 not condensing #419606
    gramp
    Participant

    Re: zwd12270w1 not condensing

    Martin. Checked that clean like new

    July 17, 2014 at 12:17 pm in reply to: whirlpool hob edges very hot #416819
    gramp
    Participant

    Re: whirlpool hob edges very hot

    thanks for your reply .it is a enamel hob and just couldn’t think how the edges on it was getting so hot as to burn .thanks again Martin .

    July 17, 2014 at 7:55 am in reply to: whirlpool hob edges very hot #416817
    gramp
    Participant

    Re: whirlpool hob edges very hot

    sorry never had it out to get a number . was more a query as to whether this was normal or not for it to get so hot ? i can go back and get a number later on today but they are thinking of just replacing the hob .

    October 23, 2013 at 10:19 pm in reply to: HOLME HWM51000SW #403324
    gramp
    Participant

    Re: HOLME HWM51000SW

    many thanks for your help
    regards gramp

    October 23, 2013 at 3:40 pm in reply to: HOLME HWM51000SW #403322
    gramp
    Participant

    Re: HOLME HWM51000SW

    thanks for your speedy response .

    February 7, 2013 at 4:30 pm in reply to: hoover hnf3157-80 not spinning #389194
    gramp
    Participant

    Re: hoover hnf3157-80 not spinning

    Cheers Martin.
    sorry for the delay on getting back to you .many thanks did not have the manual and just assumed if you set it to full spin it should do a full spin .
    cheers again for your help Alex.

    February 3, 2011 at 6:06 pm in reply to: hotpoint vtd60p tumble dryer motor stops after 30-70 mins #343514
    gramp
    Participant

    Re: hotpoint vtd60p tumble dryer motor stops after 30-70 min

    no never been asked
    no error message
    will try sensor dry and see what happens

    its my sons dryer and haven`t been to see it yet was on looking to see if anyone else had posted same fault and just stuck on a post to see if any pointers

  • Author
    Posts
Viewing 15 posts - 1 through 15 (of 29 total)
1 2