johnnyhoz

Forum Replies Created

Viewing 15 posts - 256 through 270 (of 303 total)
  • Author
    Posts
  • in reply to: Hotpoint WMA 52 #171903
    johnnyhoz
    Participant

    Re: Hotpoint WMA 52

    Thanks iadom I’m looking at the above machine on Tuesday I’ll let you know how I get on
    johnnyhoz

    in reply to: STOVES 700GC/NG #171311
    johnnyhoz
    Participant

    Re: STOVES 700GC/NG

    OK Thanks Dave

    in reply to: STOVES 700GC/NG #171309
    johnnyhoz
    Participant

    Re: STOVES 700GC/NG

    The Stoves details are as follows Model 700GE
    Pin 87BN54
    50739314
    these are the only numbers visable

    It was supplied with ceramic supports and the customer would like Cast Iron ones

    in reply to: STOVES 700GC/NG #171308
    johnnyhoz
    Participant

    Re: STOVES 700GC/NG

    ok ill get it tomorrow, thanks
    johnnyhoz

    in reply to: Taurus in DAD flyer #163067
    johnnyhoz
    Participant

    Re: Taurus in DAD flyer

    Hi all
    Iv’e just come across one of these Tarus Washing Machines in a local nusing home I service. Where will I get spares from when the need arises which by your coments will be quite soon?

    johnnyhoz

    in reply to: Hygena built in oven AHY 4120 #168949
    johnnyhoz
    Participant

    Re: Hygena built in oven AHY 4120

    Thanks Dave
    johnnyhoz

    in reply to: Miele spares #168933
    johnnyhoz
    Participant

    Re: Miele spares

    Hi harryw,

    the only place I know to get Meile spares is direct from Meile Tel No. 01235 233133

    johnnyhoz

    in reply to: Hoover Washer SE160E #164328
    johnnyhoz
    Participant

    Re: Hoover Washer SE160E

    Thanks Mike
    appreciate that
    johnnyhoz

    in reply to: Hoover Washer SE160E #164326
    johnnyhoz
    Participant

    Re: Hoover Washer SE160E

    Does anyone know the bearing sizes/part numbers for the above washer?
    johnnyhoz

    in reply to: Hoover Washer SE160E #164324
    johnnyhoz
    Participant

    Re: Hoover Washer SE160E

    Thanks Phidom,
    I just need part numbers of the bearings and seal so I can price the job,
    johnnyhoz

    in reply to: Hotpoint built-in oven Model SD98PI #163515
    johnnyhoz
    Participant

    Re: Hotpoint built-in oven Model SD98PI

    Thanks Gazza57
    I owe you one
    johnnyhoz

    in reply to: Hotpoint built-in oven Model SD98PI #163513
    johnnyhoz
    Participant

    Re: Hotpoint built-in oven Model SD98PI

    The oven was bought cheap by my customer, he was told it was a demonstration model, the shop closed down and he installed the oven several months later to find that it didn’t work.
    I found that the elements had been disconnected the cables were not marked hence the need of the wiring diagram
    johnnyhoz

    in reply to: Hotpoint built-in oven Model SD98PI #163510
    johnnyhoz
    Participant

    Re: Hotpoint built-in oven Model SD98PI

    Ok Thanks again iadom

    Contacted Creda/Hotpoint they said their engineers are the only ones allowed the drawings for health and saftey reasons, coming up with blanks all round so far, anywhere else I can try?

    in reply to: Hotpoint built-in oven Model SD98PI #163508
    johnnyhoz
    Participant

    Re: Hotpoint built-in oven Model SD98PI

    Thanks iadom
    will do, but how do you ‘bump’ a post?

    in reply to: DELONGHI DFS901SS RANGE #162914
    johnnyhoz
    Participant

    Re: DELONGHI DFS901SS RANGE

    Thanks Dave
    did you just enter the model number into the connections search to find it because I tried that and couldn’t see the stat?

    john

Viewing 15 posts - 256 through 270 (of 303 total)