mac

Forum Replies Created

Viewing 14 posts - 1 through 14 (of 14 total)
  • Author
    Posts
  • December 10, 2013 at 8:27 am in reply to: Bosch D/W shv4313gb/17 replace dispenser #406016
    mac
    Participant

    Re: Bosch D/W shv4313gb/17 replace dispenser

    Thanks for your help Paul
    John (mac)

    January 31, 2013 at 7:53 pm in reply to: Creda Cooker Model 48364 #388874
    mac
    Participant

    Re: Creda Cooker Model 48364

    went back to the cooker today and it was the base element thanks for the help and yes it is on the right hand side iadom i dont know how missed it once again thanks. John

    January 28, 2013 at 8:09 pm in reply to: Creda Cooker Model 48364 #388873
    mac
    Participant

    Re: Creda Cooker Model 48364

    Thanks for your help I will go and have another go at when the customer is in works she funny hour’s will let you know the out come thank you John

    January 28, 2013 at 7:53 pm in reply to: Creda Cooker Model 48364 #388871
    mac
    Participant

    Re: Creda Cooker Model 48364

    i did’nt realise it had a base element i’ve repaired lots of cookers but this has me beat how do get to the elemwnt

    September 8, 2011 at 9:16 pm in reply to: Zanussi ZDF490W #358376
    mac
    Participant

    Re: Zanussi ZDF490W

    Hi Martin went back to cooker today checked vent tubes for blockage they are clear I fitted new fan motor that worked fine the cooling fan was ok the customer said when she does a roast in it she has to put a towel on the floor to mop the water up, they have decided touse the cooker for a while and then replace it thanks for your help MAC

    September 6, 2011 at 3:59 pm in reply to: Zanussi ZDF490W #358375
    mac
    Participant

    Re: Zanussi ZDF490W

    They are in place but I did not check for blockage though

    January 6, 2011 at 8:26 am in reply to: Hotpoint TDC62 #340155
    mac
    Participant

    Thanks For your Help iadom Customer Called Yesterday
    And Has Decided To Replace the Machine

    January 4, 2011 at 10:24 pm in reply to: Hotpoint TDC62 #340154
    mac
    Participant

    Thanks iadom will have look Tomorrow

    January 4, 2011 at 10:18 pm in reply to: Hotpoint TDC62 #340152
    mac
    Participant

    I took the module out to the board for damage but did’nt check the contacts is this a common fault on this machine?

    November 18, 2009 at 8:16 pm in reply to: Bosch WAE24465GB/01 #303852
    mac
    Participant

    Re: Bosch WAE24465GB/01

    thanks for your help sorry it took so long to get back to you the customer went away for a few days so thanks once again mac

    May 25, 2006 at 3:04 pm in reply to: Prima Dishwasher Model LPR600 #177416
    mac
    Participant

    Re: Prima Dishwasher Model LPR600

    thanks for the help lads orderd the ntc today thanks mac

    May 24, 2006 at 7:25 pm in reply to: Prima Dishwasher Model LPR600 #177414
    mac
    Participant

    Re: Prima Dishwasher Model LPR600

    ive been back to the machine the light flashes all the time in fact the customer phoned and said she had tried it and switched off after an hour

    February 9, 2005 at 8:28 pm in reply to: Hotpoint Dishwasher Model DWF50 #124532
    mac
    Participant

    Thank you all for your help regarding the hotpoint DWF50’s customer called today and said they have obtained a commercial machine.

    January 31, 2005 at 8:00 am in reply to: Hotpoint Dishwasher Model DWF50 #124530
    mac
    Participant

    Dave you are right sorry i did’nt explain myself very well, it does change the selected cycle on it’s own. mac

  • Author
    Posts
Viewing 14 posts - 1 through 14 (of 14 total)