Forum Replies Created
-
Posts
-
Re: Hotpoint DWF32 stuck mid wash – help…
Just realised I’d not updated this page.
Finally got round to attacking DWF32 today.
Its a real pig to get into, with no obvious means to get to the gubbins. Finally figured how to get near the red microswitch rod by removing the bottom front bezel, and the galvanized plate behind it with the unit on its back.
I pushed/pulled the red rod up and down a number of times to ensure it was free, then put everything back together again.
This seems to have done the trick 🙂
First wash finished Ok and now giving it a chemical enema.I noticed when I had the unit on its back that there is a button under the base which links to the red rod allowing you to operate the microswitch without taking anything apart. Just lay the unit on its back and press this button. Useful to know if this happens again.
So thanks very much iadom – appreciate your help here. 8)
One thing I would really like to know is how to get the back, sides and/or base off if I need to change something in the future. Is there a service manual or a diagram/pictures & description. This thing is locked up like a bank safe.
Cheers.
MD
Re: Hotpoint DWF32 stuck mid wash – help…
Thnaks for your advise.
Since times are hard, and I’ve got some time off next week, I’m willing to have a look myself.
I’ve taken the washer to bits (to one degree of other) a while back, since it was leaving dishes dirty.
That was fixed.
Is the pressure chamber that big unit at the back of the washer (I think you have take the whole unit pretty much apart to get to it on the DWF32).
I’m not sure where the float micoswitch would be situated, so any advise gratefully accepted.Cheers again
Re: Hotpoint DWF32 stuck mid wash – help…
Hi again.
Well I’ve pulled the unit out and as advised tipped it back, till almost on its back.
Dry as a bone I’m afraid. 🙁
So not a flooded base in this case.Re: Hotpoint DWF32 stuck mid wash – help…
iadom wrote:Opening the door mid cycle is not advisable, the sudden change in internal pressure can lead to flooding into the base.
You need to unplug the machine, drag it out and place a few towels on the floor.
Tilt the machine back as far as you can without actually lying it flat.
If you get water running out then you do have a flooded base.
Try the machine again and if it fails in the same way then you have an internal leak that requires investigation.
OK, Thanks for the quick response.
Will try that tomorrow.
And if I don’t have water pouring out, ie no flooded base, what could it be then?Cheers
Re: Hotpoint DWF32 not cleanng properly – Help
CJAPeterborough wrote:some good news…
I suspect if you clean the pressure chamber and transfer pipe as detailed
in the thread below it will also help.
http://www.ukwhitegoods.co.uk/modules.p … ic&t=44514
The pressure chamber is that big unit at the back of the machine – requiring a full disassembly?? (top,back,sides etc)
And the transfer pipe is the ribbed pipe I see from the bottom front of the machine ?? (this one I did have a go at cleaning – although I could obviously only get at the bottom part of it)Re: Hotpoint DWF32 not cleanng properly – Help
CJAPeterborough wrote:Machine at least 8years old and if this is the first repair problem then hardly
“bad” money me thinks especially for this quality of machine?gandh1 wrote:dont get carried away cja at 8 yrs old, the motor seal will prolly need replacing as well as the impeller if heavily used with rinseaid, but still id rather spend £150 on a dwf32 than £200 on a cruddy chinese made thing…. id even spend £150 on it even tho argos have a beko for £250…
OK Gents,
All fair comment, and I have taken this on board. Thanks for the help.
As it is I do have some good news.
I have cleaned all I could get at (without a major disassembly) and gave the d/w two more chemical enema’s (OK, dishwasher cleaner bottles). This seems to have made a big difference – in that is now washes and cleans the dishes. I still don’t think its 100{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} as good as it was – but its a whole lot better.
So out of a full wash I maybe have to clean one or maybe two dishes that have been left all day will food dried on them.When it comes to rinse-aid etc – we generally use the all-in-one tablets, not separate salt & rinse-aid etc. Is this a bad thing?
Re: Hotpoint DWF32 not cleanng properly – Help
iadom wrote:
CJAPeterborough wrote:
-my money is on the flap motor which is usually a heater assemble swap.
My money would be on the same if the DWF32 actually had the motorised flap valve fitted.
Only fitted on the DWF61.
This machine uses a separate valve, part no: C00211376 which is not part of the heater box. 😉
Hi again. Hope you had a great Christmas.
Well I’ve opened the door mid cycle, and have not got wet. there is water coming from the rotors, but not I believe as much as there used to be. The rotors are turning (as I set them both at a 12 o’clock position and they have both moved from that) but they are not spinning as I open the door.
Some of the dishes are clean’ish (I wouldn’t say fully clean btw), on both top and bottom shelf, but some are plainly dirty with food still attached.
The water is getting hot as I get a good cloud of steam if I open the door in the middle of the cycle.
So if this likely to be an impeller issue as posted above or this valve you mention as above.
Only reason I ask is that its sale time now with deals at Curry’s etc.
I am not afraid of getting the tool kit to this beast, but don’t want to throw good money after bad.Re: Hotpoint DWF32 not cleanng properly – Help
iadom wrote:It could be the main circulation pump, or a problem with the heater box.
Not a simple machine to get inside but as it is a Bosch based machine well worth getting it looked at.
Thanks for that feedback.
You’re not kidding bout being difficult to get into into.
I struggled with it this morning. Managed to get the front bottom plastic kickplate and the metal plate behind removed so I could see the circ motor and drain pump, but could not get at them. The only thing I could get at was the circ motor capacitor.
Have verified that the circ motor and drain rotor turn by hand easily via the internal sump holes.
I don’t think that there is an issue with the heater as I ran the dishwasher empty this morning with a cleaner bottle inside. The 65deg wash produced the necessary heat to melt the wax seal on the bottle.
I’ll try another wash tonight, but I suspect the circ motor is working but not well enough. So is this likely an issue with the motor or the capacitor?Also what I could do with knowing is how to get the bottom and sides of the unit off so I can get at the circ pump and check all the pipes are debris free.
Cheers.
Re: Hoover AE130 Washer issue during Rinse phase
Gents thanks for your advise, and promptness. 🙂
Martin, forgot to mention – I have just replaced the brushes on the washer as recently the unit would not spin at all. Since then the unit is spinning OK for distribution, washing, final spin so I don’t think the motor/armature is the issue here.
