norbellini

Forum Replies Created

Viewing 15 posts - 16 through 30 (of 34 total)
1 2 3
  • Author
    Posts
  • July 4, 2011 at 10:24 am in reply to: White Knight dryer query #354655
    norbellini
    Participant

    Re: White Knight dryer query

    dont have a hammer :rolls: but i would like to know how you get the heat exchanger out .it has a strap but it wont shift without going mad Just a bit of help please

    May 3, 2011 at 10:16 pm in reply to: noise from gas cooker grill #350513
    norbellini
    Participant

    Re: noise from gas cooker grill

    Thats seems a good place to start i will give it a go in the morning Oh! i reckon using the wifes toothbrush would be best

    May 3, 2011 at 10:02 pm in reply to: noise from gas cooker grill #350511
    norbellini
    Participant

    Re: noise from gas cooker grill

    thanks for the answer Just it hasnt done it for 5 years and now it starts

    February 18, 2011 at 4:33 am in reply to: fitting Indesit door seal #344223
    norbellini
    Participant

    Re: fitting Indesit door seal UPDATE

    door seal fitted .I thought it might be fiddly but in fact it was pretty straightforward so thanks again for the info chaps 🙂

    February 14, 2011 at 1:45 pm in reply to: fitting Indesit door seal #344222
    norbellini
    Participant

    Re: fitting Indesit door seal

    got it off thanks for the advise chaps eh its a bit different in here compaired to me 10 year old bosch i had .Still that buga used suspension legs of a kids pram thanks again

    February 14, 2011 at 1:09 pm in reply to: fitting Indesit door seal #344220
    norbellini
    Participant

    Re: fitting Indesit door seal

    so you dont work from the top , you perform through the door thats fine thanks for the advise . Tacking the fronts up tut tut

    February 14, 2011 at 12:40 pm in reply to: fitting Indesit door seal #344218
    norbellini
    Participant

    Re: fitting Indesit door seal

    i have removed the front soap tray and pcb board but appears that the front panel is tack welded . How do you get to put in a new seal WIXE 127
    regards

    February 10, 2011 at 1:38 pm in reply to: fitting Indesit door seal #344217
    norbellini
    Participant

    Re: fitting Indesit door seal

    thanks ill dive in
    regards

    January 10, 2010 at 8:30 pm in reply to: wifey puts candle in dishwaher grat #308415
    norbellini
    Participant

    Re: wifey puts candle in dishwaher grat

    TRICITY BENDIX ECO SAVE DH090
    thanks

    December 22, 2008 at 9:29 am in reply to: not sure about black spots (bosch washer) #272192
    norbellini
    Participant

    Re: not sure about black spots (bosch washer)

    that sounds like whats happening i must admit we havnt done enough of these high temp. washes i will take your advise .
    thanks

    December 21, 2008 at 9:58 pm in reply to: not sure about black spots (bosch washer) #272190
    norbellini
    Participant

    Re: not sure about black spots (bosch washer)

    thanks for the advise , i will do that and give it a good few “washes” with soda crystals and change the drum seal. i thought if it was the bearings and they are sealed by the looks, they would be rumbling if they got to the point of leaking grease dont you think?

    November 26, 2008 at 9:24 am in reply to: new panasonic microwave (puzzling part) #269557
    norbellini
    Participant

    Re: new panasonic microwave (puzzling part)

    and thats the fella, thank you

    October 26, 2008 at 6:04 am in reply to: freezers for garages #266575
    norbellini
    Participant

    Re: freezers for garages

    so would you say that a chest freezer would be better suited to a garage. i am told they work in a different way

    September 12, 2007 at 5:57 pm in reply to: Knocking sound at low RPM from Bosch Logixx 1400 Express #224010
    norbellini
    Participant

    Re: Knocking sound at low RPM from Bosch Logixx 1400 Express

    just a point penguin my shockers have failed on my BOSCH CLASSIXX and on inspection the ones fitted to mine are flimsy plastic slider ones .Yet on the parts list they look a lot more robust what is the story on these modifications i am going to write to BOSCH and ask whats going on when they want £100 for new ones on a 3 yearold model with little use
    regards norbellini

    July 28, 2007 at 9:29 pm in reply to: bosch classixx 1000 spin query #222837
    norbellini
    Participant

    Re: bosch classixx 1000 spin query

    e-nr wfl2066gb/08 fd8411600757
    drum is nice and smooth with no play i think the bearings are ok . must say drum isnt very stable on the legs. It just seems a bit quick for suspension legs to pack in. Saying that i remember bogging them when i put a new heater in and they did look “skinny”
    rgeards

  • Author
    Posts
Viewing 15 posts - 16 through 30 (of 34 total)
1 2 3