paul161201

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 37 total)
1 2 3
  • Author
    Posts
  • May 30, 2011 at 4:49 pm in reply to: Hotpoint wma50 #352415
    paul161201
    Participant

    Re: Hotpoint wma50

    Just to let you noe repaired the pcb and harness machine works again

    May 28, 2011 at 6:21 pm in reply to: Hotpoint wma50 #352414
    paul161201
    Participant

    Re: Hotpoint wma50

    I think i located the problem.
    I had a look at the machine again and removed the motor harness the plug that connects to the motor two of the pin were short circuiting where the plastic motor plug had melted.

    I have replaced this plug with one from a scrap machine
    I have a bit of difficulty puting the top back on the plug i just pushed it into place with a pair of pliers but It doesnt seem very strong a hard pull and i think it would come off

    May 28, 2011 at 3:58 pm in reply to: Hotpoint wma50 #352412
    paul161201
    Participant

    Re: Hotpoint wma50

    The brushs still have about 1/2 an inch left on them. When i turn the motor by hand one way its smooth. When i turn the opposite way it seems to have a little rattled
    I metered the motor again The coils seem and the armature have a low readings
    but i now have a dead short between yellow and black

    May 21, 2011 at 6:40 pm in reply to: washing machine parts #351944
    paul161201
    Participant

    Re: washing machine parts

    Yes i am in the trade will apply for trade membership

    May 21, 2011 at 6:33 pm in reply to: Will motor from Zan f1245w fit zan FJ1296 #351940
    paul161201
    Participant

    Re: Will motor from Zan f1245w fit zan FJ1296

    Zanussi F1245w motor fits 89 different Zanussi models. Model FJ1296 is not one of them from the information i have
    What is a PNC number?

    January 25, 2011 at 10:02 pm in reply to: LG WM-1375FHB #342411
    paul161201
    Participant

    Re: LG WM-1375FHB

    I replaced the doorlock and the machine started to smoke like mad so binned it

    January 12, 2011 at 8:07 pm in reply to: Hoover VHD814 Washing Machine #340250
    paul161201
    Participant

    Re: Hoover VHD814 Washing Machine

    Sounds like the door interlock.

    November 12, 2010 at 8:42 pm in reply to: Creda Aspire Solarplus cooker #335653
    paul161201
    Participant

    Re: Creda Aspire Solarplus cooker

    model number is 48902 but returns zero results

    October 28, 2010 at 7:26 am in reply to: Hoover AA230 #333937
    paul161201
    Participant

    Re: Hoover AA230

    I done that and still will not spin

    October 26, 2010 at 7:40 am in reply to: Hoover AA230 #333935
    paul161201
    Participant

    Re: Hoover AA230

    it runs thought the program fine but at the end of the program the water is pumped out but the drum will not spin. and the cycle finishes normally. Leaving the cloths wet.

    October 25, 2010 at 9:30 pm in reply to: Hoover AA230 #333933
    paul161201
    Participant

    Re: Hoover AA230

    It will not spin i have checked the brushes the connections the sump hose and which are all fine

    August 31, 2010 at 7:31 am in reply to: Hoover washing machine 1300 special edition model number is #329176
    paul161201
    Participant

    Re: Hoover washing machine 1300 special edition model number

    the drum will only move in one direction

    August 6, 2010 at 4:28 pm in reply to: Hotpoint WD71 Door open #326943
    paul161201
    Participant

    Re: Hotpoint WD71 Door open

    It just a temp repair to see if the PCB still works
    the circuit board has blow a track which i have repaired
    I
    So do i just join the Live and common together
    thanks

    May 27, 2010 at 5:42 am in reply to: Matsui MWM145W starts cycle and flashes #321128
    paul161201
    Participant

    Re: Matsui MWM145W starts cycle and flashes

    The program ready light blinks and the program end light blinks

    Also what is a Configuration
    error software problem?

    May 19, 2010 at 11:37 am in reply to: Photo of servis easi logic module #320552
    paul161201
    Participant

    Re: Photo of servis easi logic module

    I just put in a new module I took a photo of the old one but the photo is not showing the end terminals which sit on top of the board They are colour coded
    One block has a green line the other has a purple line and one is a signal red
    the part number of the PCB is 546033801

  • Author
    Posts
Viewing 15 posts - 1 through 15 (of 37 total)
1 2 3