Penguin45

Forum Replies Created

Viewing 15 posts - 16 through 30 (of 19,678 total)
1 2 3 … 1,310 1,311 1,312
  • Author
    Posts
  • November 28, 2011 at 1:19 am in reply to: Caple DI604 #364419
    Penguin45
    Participant

    Re: Caple DI604

    Flood protection activated – water in the base tray.

    Chris,
    P45.

    December 17, 2010 at 1:25 am in reply to: Bosch WVT1260GB/01 #338785
    Penguin45
    Participant

    Re: Bosch WVT1260GB/01

    Thank you.

    Chris.

    October 26, 2010 at 12:04 am in reply to: AEG LAVAMAT 6955 Damper query #333850
    Penguin45
    Participant

    Re: AEG LAVAMAT 6955 Damper query

    Two dampers – 8996453289507.

    Check for leakage from the soap hose – that’s what usually does in the right hand one.

    P45.

    October 25, 2010 at 11:58 pm in reply to: Miele G645SC relay #332715
    Penguin45
    Participant

    Re: Miele G645SC relay

    P/no is T.Nr.05008870. You’ll pay Miele lots.

    P45.

    October 25, 2010 at 11:42 pm in reply to: CDA 446, think its a whirlpool dishwasher. #333859
    Penguin45
    Participant

    Re: CDA 446, think its a whirlpool dishwasher.

    If the drain pump is pulsing, it’s a board fault.

    P45.

    September 22, 2010 at 12:33 am in reply to: Cookworks WQP8-9239 – just stops! #330102
    Penguin45
    Participant

    Re: Cookworks WQP8-9239 – just stops!

    Don’t waste your time. Send it back as unsuitable, then spend a bit of tiime and find a proper a proper dishwasher and be prepared to pay accordingly.

    Chinese rubbish.

    Penguin45.

    August 23, 2010 at 11:51 pm in reply to: PDW080 Stuck Timer & No Heat #328661
    Penguin45
    Participant

    Re: PDW080 Stuck Timer & No Heat

    Safety-cut out has tripped. Buy THIS.

    Penguin45.

    July 25, 2010 at 6:18 pm in reply to: zanussi fjr1454w takes to long to complete cycle #326169
    Penguin45
    Participant

    Re: zanussi fjr1454w takes to long to complete cycle

    Check wash heater.

    Penguin45.

    July 24, 2010 at 12:45 am in reply to: whirpool awg345/4 #326115
    Penguin45
    Participant

    Re: whirpool awg345/4

    It’s a SMEG. E09 is not a recognised code.

    Chris.

    July 24, 2010 at 12:25 am in reply to: Smeg DW1612 Lights 4 + 5 ON ? #325838
    Penguin45
    Participant

    Re: Smeg DW1612 Lights 4 + 5 ON ?

    4+5 indicate that the programme has completed, so switching off and on again should allow you to select a new programme.

    Penguin45.

    July 24, 2010 at 12:00 am in reply to: Bosch Dishwasher sgs4012 not heating #325479
    Penguin45
    Participant

    Re: Bosch Dishwasher sgs4012 not heating

    It’ll be the usual underfilling issue. Lots of posts refer.

    Penguin45.

    July 23, 2010 at 11:58 pm in reply to: ikea d/w fault #325839
    Penguin45
    Participant

    Re: ikea d/w fault

    It’s a SMEG-built slimline machine – define “surging”.

    Penguin45.

    July 23, 2010 at 11:48 pm in reply to: Diplomat ADP8322 spilling over! Help! #325279
    Penguin45
    Participant

    Re: Diplomat ADP8322 spilling over! Help!

    Four flashes is the no drain error. Commom sense would suggest that bailing out the machine before tipping it would be a good plan. The drain pump is a twist-fit; accessible through the front lower panel – no need to tip he machone at all.

    Penguin45.

    July 23, 2010 at 9:26 pm in reply to: smeg grill element #326105
    Penguin45
    Participant

    Re: smeg grill element

    806890527

    Chris.

    July 13, 2010 at 11:31 pm in reply to: Zanussi ZJD-12191 Cycle won’t start #325229
    Penguin45
    Participant

    Re: Zanussi ZJD-12191 Cycle won’t start

    Usually some sort of corruption issue caused by earth leaks on the motor or heaters. You need a Meggar or insulation tester to solve this one.

    Power off if you’re going in yourself.

    Penguin45.

  • Author
    Posts
Viewing 15 posts - 16 through 30 (of 19,678 total)
1 2 3 … 1,310 1,311 1,312