[Rai]

Re: BUSH DISH WASHER WQP8-9347

Hi Dave, Thanks a lot for your response. Luckily, I once again decided to have a go at the flood switch by taking out housing that holds the switch, on the polystyrene (the) Switch activator , I noticed that some debris was stuck on it and this was pushing the switch upwards and as a result of this the machine was not functioning and rendering the message as E4.

After removing the debris that got stuck on the switch activator, I refitted the switch housing and Wov ❗ ❗ the machine started working normally.

I wish to thank you very much for all your helpful Advice & time. Kind regards. 😀 😀
Rai

[Rai]

Re: E4 Error on Dish Washer

Hi Dave, thanks for your reply to my posting. Firstly, I wish to apologies for creating a new post instead of continuing with the earlier posting.

I, agree that I should have taken a photo of the wiring position on the switch before actually pulling out the wires.

I doubt the door switch because immediately once the door is opened and power is applied the E4 is displayed. Function switches (Touch Pads) has got no effect at all and once the door is closed, with the E4 sign still displayed, there is some noise like a motor rotation or probably a pump being activated. This sound continues for some time and then stops.

However, when the machine was working fine, it used to do the following:

once the door is opened and powered up the display shows as 00, upon selection on the function /program switch the appropriate function LED would light up and once the door is shut the machine carries out its function.

Do you think the fault is on the other section on the machine as there appears to be no water on the base, flood switch seems to be working ok, probably the touch pad function switches are not working.

Where is the door switch normally located, I can also check the same with the meter is its working. Thank you very much

Any help, guidance, advice will highly be appreciated.

Kind regards. Rai

[Rai]

E4 Error on Dish Washer

Hi All I had earlier on posted a message on the forum regarding my Bush Dishwasher,

The original problem seems to now have changed from display of 2 dashes (- -) only to Error code E4 now.

I have dismantled the switch and checked it with a meter and the switch seems to be working ok its a three pole micro switch one position is on and when pushed it is breaking. The other position is Push to make. I hope I am reconnecting the wires right way as I didnt take a note of the actual position of the wires on the switch

Using / trying push to break connection is showing E4.and when connecting to, push to make it is only showing 2 dashes (- -) on the display. Will appreciate any advice on this.

Secondly, the 2 wires that goes on the switch is showing continuity when wires itself are tested after disconnecting from the switch is this correct ?.

Probably the fault lies somewhere else.

Any advice / help rendered on this problem will be highly appreciate.

Kind regards. Rai

[Rai]

Re: Hotpoint Tumble Dryer CTD40P

Hi Iodam. I ordered the correct Element from the supplier you suggested.I have fitted the same on the dryer and Its working fine. Thank you very much for your Kind advice and assistance. Regards. Rai

[Rai]

Re: Hotpoint Tumble Dryer CTD40P

Thank you very much for all your assistance I will order it from the supplier you have suggested, they seem to be having the type required. Once again thanks and regards.
Rai.

[Rai]

Re: Hotpoint Tumble Dryer CTD40P

Hi iadom, Thank you very, very much for your assistance, in the meantime I will arrange to return the Heaters that I have purchased from E Bay as they had mentioned this heaters are for CTD40P. I will source from other suppliers. If you may have any information on who could supply the correct type then please let me know accordingly.

Thanking you for all the advice and assistance rendered over this matter.

Rai

[Rai]

Re: Hotpoint Tumble Dryer CTD40P

Hi Thank you for your prompt reply, the wiring configuration on the new heaters were exactly the same color coded and positioned. It has got the 3 items fixed on the Heater mounting bracket which I assume are 2 stats and a thermal cut out units.

The Replacement heaters were purchased from E Bay. The sellers advert says replaces C00258828, it looks exactly the same to the one removed. Photo of the new heaters attached. The older Stats and cut out are all black in colour the new one has got 2 black coloured and 1 white.

Thanks for informing me about Fire safety, after seeing your response I had submitted the online report to hotpoint.
The Model NO is CTD 40P Serial NO 601240071.
Will very much appreciate for your feedback on this matter.
Thanks and Kind regards. Rai

[Author]

Posts