razor

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 143 total)
1 2 3 … 8 9 10
  • Author
    Posts
  • February 14, 2015 at 9:58 pm in reply to: Hotpoint WD860 31135 Display says ON and the red light on #424624
    razor
    Participant

    Re: Hotpoint WD860 31135 Display says ON and the red light

    one of the buttons stuck,take board out and check buttons or child lock on maybe??

    January 19, 2014 at 7:16 pm in reply to: hotpoint wmud 960 #407829
    razor
    Participant

    Re: hotpoint wmud 960

    sorry never even noticed that model was incorrect, think he meant WMD960.

    could well be incorrect file setting on board or wrong board as you have said iadom

    January 18, 2014 at 10:28 pm in reply to: hotpoint wmud 960 #407826
    razor
    Participant

    Re: hotpoint wmud 960

    maddie wrote:Can anyone give me advice number of problems with machine.
    1 no water inlet at valve.changed for new as other was burnt out also got a recondition module from a company on a exchange basis.Now when i power up and select awash pump starts for 2 seconds and cuts out and repeats it self over and over again.also water switches on and cuts of after 1 second and keeps repeating this.After about 7 mins it displays F02 fault.i have cleaned filter but found nothing.i have checked wiring on module and all are snug and tight.Any help please i am a lost with this now


    Maybe the new module faulty or wiring from motor to module faulty

    F02 is motor tacho fault

    January 10, 2014 at 9:45 am in reply to: Indesit WIDL126 very bouncy #407451
    razor
    Participant

    Re: Indesit WIDL126 very bouncy

    Morning

    is it spinning ok, have you check your pump filter for any blockages? could also be suspension needing replaced or suspension pin maybe that’s came out.

    as always unplug appliance

    January 10, 2014 at 1:02 am in reply to: Cannon CH60GTCF #407450
    razor
    Participant

    Re: Cannon CH60GTCF

    side panel removal – only remove 1 panel at a time…

    remove main door assembly , if removing left hand side panel only

    undo 11 screw at the front left hand side including the door hinge fixings or the 7 screws at the front right hand side, to whichever panel you require to remove

    undo the 7 screws from the left hand or right side panel rear

    pull the relevant side panel clear.

    🙂

    November 14, 2013 at 7:21 am in reply to: Hotpoint WDD960 Dryer NTC #404435
    razor
    Participant

    Re: Hotpoint WDD960 Dryer NTC

    Part No I have found is C00098739

    November 6, 2013 at 7:38 am in reply to: Door flashing error #403976
    razor
    Participant

    Re: Door flashing error

    If the door is still locked, check carbon brushes, and make sure appliance is unplugged.

    May 27, 2013 at 8:21 am in reply to: oven not fully heating #395577
    razor
    Participant

    Re: oven not fully heating

    Hello shurkin1

    probably be faulty thermostat

    March 13, 2013 at 11:34 pm in reply to: Zanussi FL1281 Door Glass #391983
    razor
    Participant

    Re: Zanussi FL1281 Door Glass

    check ebay item number 261101035493, trying to remember if thats same door?

    just checked there, wrong door that one

    February 28, 2013 at 8:08 pm in reply to: Hotpoint AQLF9D69UK – Parts Diagram needed #391176
    razor
    Participant

    Re: Hotpoint AQLF9D69UK – Parts Diagram needed

    Anyone able to assist 🙂

    thanks

    February 27, 2013 at 11:35 pm in reply to: Hotpoint AQLF9D69UK – Parts Diagram needed #391175
    razor
    Participant

    Re: Hotpoint AQLF9D69UK – Parts Diagram needed

    hello madangler1 , when tilting it to the side the black gromit is underneath the tank, size about of a 10p, if that helps

    February 17, 2013 at 11:07 pm in reply to: Indesit WIDXL146UK #390111
    razor
    Participant

    Re: Indesit WIDXL146UK

    Wash heater – C00255452,

    only thing can find for the dryer ntc is this C00264605 if that helps

    February 10, 2013 at 12:27 pm in reply to: Hotpoint Dryer TCD970 Help #389768
    razor
    Participant

    Re: Hotpoint Dryer TCD970 Help

    thanks iadom 🙂

    February 10, 2013 at 10:30 am in reply to: Hotpoint Dryer TCD970 Help #389766
    razor
    Participant

    Re: Hotpoint Dryer TCD970 Help

    Many thanks iadom for quick reply

    would you happen to have the fault code list for these

    cheers

    Raymond

    December 14, 2012 at 1:06 am in reply to: WF240P program dial part number #386313
    razor
    Participant

    Re: WF240P program dial part number

    C00113952

  • Author
    Posts
Viewing 15 posts - 1 through 15 (of 143 total)
1 2 3 … 8 9 10