Page 6 – UK Whitegoods

Forum Replies Created

Viewing 15 posts - 76 through 90 (of 133 total)

← 1 2 3 … 5 6 7 8 9 →

Author

Posts
September 19, 2008 at 12:02 pm in reply to: Elderly Electrolux WD1034 #262909

rogue_element
Participant

Re: Elderly Electrolux WD1034

sorry clicked on wrong link please see below

hi errr been a bit since i have seen one but i think your right . the motors on these w/m were built like tanks. the part number you need is:

50068807002

rogue

August 21, 2008 at 1:51 pm in reply to: Payment Issues & Other Problems #260224

rogue_element
Participant

Re: Payment Issues & Other Problems

cash customer`s with bass in there hands.

July 30, 2008 at 12:53 pm in reply to: Zanussi ZDT6255 Flood Protection #258773

rogue_element
Participant

Re: Zanussi ZDT6255 Flood Protection

HI

ERRRRR BAY LEAF MAY HAVE BEEN THE PROBLEM . DRAIN BASE AND TRY
GOOD LUCK

ROGUE

July 30, 2008 at 12:27 pm in reply to: Zanussi ZDT6255 Flood Protection #258771

rogue_element
Participant

Re: Zanussi ZDT6255 Flood Protection

HI

1st UNPLUG
2ND MAKE SURE ITS THE RIGHT PLUG
3RD REMOVE LEFT HAND SIDE PANEL , STAND ON TOWLES DRAIN BASE BUY TIPPING SLIGHLTLEY OVER THIS WILL RESET ANTI FLOOD.

NOW ALL YOU NEED TO DO IS WORK OUT WERE ITS LEAKING FROM .

ROGUE

July 30, 2008 at 12:24 pm in reply to: vintage bendix dishwasher question #258748

rogue_element
Participant

Re: vintage bendix dishwasher question

HI

WASH PUMP OBSOLET , UNSURE IF THERE IS A BEARING REPLACEMENT KIT

ROGUE

July 30, 2008 at 11:56 am in reply to: ZANUSSI ZWF1431 #258769

rogue_element
Participant

Re: ZANUSSI ZWF1431

HI TRY BLUE LOOM

CHEAPEST OPTION

ROGUE

July 28, 2008 at 3:48 pm in reply to: BEKO WMB10W heater mounting? #258586

rogue_element
Participant

Re: BEKO WMB10W heater mounting?

Heater support

Heater support

Heater holder bracket

Suitable for: Beko: • WM 1010/ 1210 W/ 1510 W/ 1510 • WM1010 / 1080 / 1210 / 1210-K1/ 1260/ 1…

From £2.13
SRP: £2.94

In Stock
Beko

Code: BEK2801660101

ROGUE

July 18, 2008 at 12:49 pm in reply to: zan zsf2240 #257792

rogue_element
Participant

Re: zan zsf2240

hi

do you need salt ? if so reed snsor on salt pot
is rinse aid leaking ? have you turned down ?

replace dispenser

rogue

June 4, 2008 at 10:54 am in reply to: Zanussi WJD 1667W #253747

rogue_element
Participant

Re: Zanussi WJD 1667W

NO PROB`S
ROGUE

June 4, 2008 at 8:59 am in reply to: Zanussi WJD 1667W #253745

rogue_element
Participant

Re: Zanussi WJD 1667W

com error on board may be blue loom and / or pcb

rogue

May 30, 2008 at 6:23 am in reply to: tubs dumped – disgusting :( #253264

rogue_element
Participant

Re: tubs dumped distgusting

IT WAS`NT ME

ROGUE
😆

May 30, 2008 at 6:21 am in reply to: A Tricky Job? – Whats the hardest repair you have done? #253205

rogue_element
Participant

Re: A Tricky Job? – Whats the hardest repair you have done?

ALEX WROTE

Worse than that… Zanussi f/freezer insulation re-foams in the 1980’s.

I DID NOT MIND DOING THEM EASY MONEY ( UNLESS THEY HAD NOT BEEN DEFOSTED)

ROGUE

May 29, 2008 at 12:50 pm in reply to: AEG Condensing T/D 916014098 #252840

rogue_element
Participant

Re: AEG Condensing T/D 916014098

HI GOOSE
HAVE YOU LOOKED AT THE SENSOR STICK ON REAR ON DRUM ? MAY JUST NEED CLEANING
ROGUE

May 29, 2008 at 8:26 am in reply to: A Tricky Job? – Whats the hardest repair you have done? #253198

rogue_element
Participant

Re: A Tricky Job? – Whats the hardest repair you have done?

BOTH CAVITYS ON A DOUBLE OVEN ERrrrrrrrr

ROGUE

May 14, 2008 at 11:42 am in reply to: New tool for dealing with water escapage #250522

rogue_element
Participant

Re: New tool for dealing with water escapage

AGREE WITH ANDY

NO ONE GET`S IT FOR NOUGHT

ROGUE
Author

Posts

Viewing 15 posts - 76 through 90 (of 133 total)

← 1 2 3 … 5 6 7 8 9 →