Forum Replies Created
-
Posts
-
Re: Hotpoint Rl34G makes terrible noise
i turned it up to 5 from 3 and 10 mins later it had still not turned on, i was not saying that the dent would affect anything what i was referring to was he way t may have been handled for it to get the dent also the cracked salad bowl, not to happy about just hoping its working ok if you know what i mean
the gurgling soumd is on all the time the motor is on, when the motor cuts out then it stops, i have never heard a fridge make this coninual noise, my other one the RLA30 (same fridge older model) never made such noises, maybe without the damage to the fridge i wouldnt be too concerned but knowing its obsiouvlsy taken some knocks has me a little concerned
Re: Hotpoint Rl34G makes terrible noise
stripey wrote:Hi
Some refrigeration products do make a gurgling noise for a while but these do normaly settle down. I doubt very much if a dent in the side would cause this problem as the compressor is located at the bottom on the rear of the appliance.
If it is only less than a week old you do have a returns agreement with curry’s you can reject anything within the first28 days. I wouldn’t bother contacting hotpoint I would go back to the retailer.
thanks, like i say im also concerned that the control button doesnt clcik it on or off like the other did, surely if i clcik down to 1 and its at 3 ths should turn the motor off, and again if motor is not running at three and i turn it to 5 it should force the motor on?
Re: Hotpoint Rl34G makes terrible noise
also when i turn the temperature contol (numbered 1-5) on the font, currently at three, when i turn it to 1 0r 2 it doent click and turn motor off, the same as if motor isnt running and i tun it to 4 or 5 it doesnt turn motor on, which my old model RLA30 used to
Re: Any Hot and Cold fill machines??
don wrote:
iadom wrote:
I am not sure but I think there may be a Whirlpool that still has H+C fill, but that may also have been phased out by now.
Jim.
Just been discontinued but someone may have some left. IIRC it was the AWOD5706 and the AWO3571, but you will need to check these models instore to be sure.
Have a read here sassie of Jims link 😉 http://tinyurl.com/ywqc9z
Don
Thank you don, i have just read that and yes that makes total sense, but i believe mine is pulling off the hot water on everywash and i only use 40 cotton hence maybe why my clothes never seem to be washed, my machine never removes any stains off clothes, maybe its time for a new one, even after spending all day replacing a door gasket 😳
Re: Any Hot and Cold fill machines??
If it doesnt fill with both, why is it plumbed into both 😳 Is it for the econonmy wash? I know dumb blonde, but it is monday 😆
Re: replacing creda machine door seal tool query
canshefixit wrote:I have removed the top of the machine and access to the screw is through a slot above the timer knob, allowing me to remove the front fascia and therefore the front panel.
Oh welll worth a shot, mine i only had to remove the washer draw and front came off, it took me hours upon hours to work out how to do mine, and once i got front off, it was all sorted withing an hour, hang in there someone may come to advise
Good luck im sure you will get there
Re: replacing creda machine door seal tool query
I know this is going to sound daft, but can you not get to screw from the top?
Re: Indesit W822R door-drum seal replacement HELP!!!
Martin wrote:
*sassie* wrote:
Hi. Im not sure if it will be the same as mineNo *sassie* the Indesit W822R is completely different. 🙁
The inner clamp ring is held on in the 12 o’clock position with a 7mm nut and bolt. Release that (through the door aperture by the way) and pull it clear. 😉
OOps sorry, just ignore me, was thinking me clever 😳 And i did change me loo flush yesterday too, thought i was becoming a handy women 😀Re: Indesit W822R door-drum seal replacement HELP!!!
Hi. Im not sure if it will be the same as mine, but i needed to unscrew the three screws that are in the dispenser draw which roves the control panel, and then i was able to remove the front of the machine, it is held round the drum with another wire which has a long screw on ot, unscrew till it releases, then replace with new seal
sorry if it is not the same as mine, but thought i would post incaseRe: How to remove/replace the door gasket on Hotpoint WMA66
hotpnt wrote:a job well done, congrats sassy, now if i need another engineer to take on ill give you a call, really,
Thanks, had the stoopid idiot i phoned not told me to look for screws underneath the machine to remove the front it would have been alot sooner job done, once i had removed the front it was a quick job done, then just to remember where each screw went back, 😳 But i am quite chuffed with meself 😀
This Forum Could Do with A Thanks Button 🙂
Re: How to remove/replace the door gasket on Hotpoint WMA66
OMG i have done it, 12 hours later and its all done, i cant bleeding believe it 😀
😀 😀 THANKS FOR ALL YOUR HELP 😀 😀Re: How to remove/replace the door gasket on Hotpoint WMA66
the screws i have removed are two from door latch, and two from bottom behind the guard, i just cannot see what is keeping the front on apart from what looks like 4 plastic pegs but just cant work out what they are doing, tried pushing front up and down but nothing, i will keep on till i probably complete knacker frame 😳 I am a woman afterall 😉
Re: How to remove/replace the door gasket on Hotpoint WMA66
Brilliant i cant get anyone out to it and now aint got a washer as cut the other one to get to other spring, removed every screw i can think of and cant get front off, any ideas appreciated 😳
Re: How to remove/replace the door gasket on Hotpoint WMA66
right thats the outer wire off, now trying to tackle the inner one which seems to be a spring loaded long screw, wish me luck 😳
No way on this planet am i going to be able to shift that one, so time to call someone in, thank you Jim for all your help xxRe: How to remove/replace the door gasket on Hotpoint WMA66
iadom wrote:Might be best if you don’t feel up to removing the front panel, some of the retaining straps used are rather awkward to get back on. In the meantime have a read of this atricle. http://tinyurl.com/37wxzx
Jim.
Thanks Jim, I have already read that, my machine has always been used daily and cleaned monthly but it the crap wont come off tried everything, it may be a start if i could work out how to remove the front wire, it has like a white block of plastic at the top and i cant even work out how to remove that, i have tried pushing it up, pushing to either side 😳 any other ideas 😳 God i wish i was a man at times – lol
