[TELL]

Re: siemans cooker, need pt/no please.

dave, checked out the site gegsy gave me. told me to get back in touch with you on a price for the element, as his site was mostly for the general public, can you give me a price on the element-443526?. connect have it at £24.57, but also have in stock.
TELL..

[TELL]

Re: siemans cooker, need pt/no please.

thanks gents, thats sorted,
ps. forgot about that site, dave. old grey matter is going to mush,
TELL.

[TELL]

Re: Whirlpool gen 2000 G2PDWI/1. reverts back back to rinse

thanks for the feedback lads, certainly sounds like an NTC fault F1, contineous flash. but could the board be at fault, if i’m getting a reading of 67k at 14 degC through the wiring through the connecter off the pcb.
remember, i had the motor, d/pump and all other functions, running on the first test. and these boards are about £80.00.
TELL..

[TELL]

Re: Whirlpool gen 2000 G2PDWI/1. reverts back back to rinse

brian,
any idea on the the readings i should be getting on the NTC,
TELL..

[TELL]

Re: Whirlpool gen 2000 G2PDWI/1. reverts back back to rinse

hi, EFS
the 5th light flashes at a constant rate, with no pause’s at all. had tried to count to see if there was a sequence, re: known error codes.
TELL..

[TELL]

Re: 5Kv 700M/amp fuse, who has these?

thanks bazaa6. will keep that in mind.
TELL..

[TELL]

Re: Belling cooker mod 789ss, side by side double.

ta dave.
TELL..

[TELL]

Re: M/wave wiring diagram req’d ??.please.

davecas, thanks for your input. when testing the diode, and bleed resistor on the cap, I (thicky) tested the bleed and diode together giving me a reading, ok. diode to chassis blown.
TELL..
p.s. lads thanks for your input.

[TELL]

Re: M/wave wiring diagram req’d ??.please.

on the job now checking through, fingers crossed. thanks gentlemen. will keep you informed.
TELL..

[TELL]

Re: M/wave wiring diagram req’d ??.please.

will go through the wiring and components again, and isolate the LV side at trans, to check it out.
TELL..

[TELL]

Re: M/wave wiring diagram req’d ??.please.

magnetron filament has gone down to earth orig fault, new mag in, diode ok, bleed resistor ok, cap ok, and my reading on the transformer windings are ok.
the m/wave will power up to setting to cook, and fuse ok, wont blow.
but set on to cook ie… press start, it pops the fuse.. thats why i need a diagram for the pcb. as this earth lead off it has a circuit through to earth?????.
TELL..

[TELL]

Re: M/wave wiring diagram req’d ??.please.

diagram not in the casing etc, no book from cust, what happened is the
8 amp safety blown fuse blown, tested the components, trans, cap, diode, etc, and found magnetron filament shorting to earth, goosed, fitted new mag, test m/c saftey fuse blown again. went back into components testing, found the relay blk, and brn wires run back through to the main control panel and are giving a readind down to earth,????.
there is an earth lead on the main p.c.b which runs to a door monitor (microswitch) and down to earth. i’m not getting any other reading to earth off anthing else.??
TELL..
P.S. apprieciate the response, Davecas & dpm.

[TELL]

Re: M/wave wiring diagram req’d ??.please.

can anybody give me a site on the internet to get this wiring diagram, getting desperate now, thanks
TELL..

[TELL]

Re: Diplomat ADP8902 Dishwasher 5th light flashing??

thanks again dave
TELL..

[TELL]

Re: Bernstien group fridge B/I door hinges

thanks dave . e’mail on its way to andy.
TELL..

[Author]

Posts