[TELL]

Re: smeg washer/drier bearings

thanks for the feedback chris, much apreciated.
TELL..

[TELL]

Re: AEG Lavamat 74335 aborting pgm

is there a fault code displayed on the facia panel, ie (err 33).normally these m/c’s show a code?.
TELL..

[TELL]

Re: neff dryer R4380XOEU/04

funky, i would certainly check the carbon, and the the earth strap/lead -connections onto the board.
p.s. just a thought are you testing this with a dry load, or a damp load?. if its dry it wont measure the resistance, thinx’s its finished?.
TELL..

[TELL]

Re: danish glass fronted fridge VESTFROST

has anybody got the part numbers, and where to get these parts from aswell, whitegoodsman, has responded early on, but no contact number has been left. need to get these fairly quickly.
ta TELL..

[TELL]

Re: danish glass fronted fridge VESTFROST

have you a contact tel; no.??and name. or you can p.m. me
ta TELL..

[TELL]

Re: w/pool d/washer ADG993 (854299315120)

thanks gegsy, and penguin. 1/2 thought that was the fault. but could not see anything on the board, wanted to make sure. all components checkout ok, any idea why its gone??.
ta TELL..

[TELL]

Re: indesit bearings shaft size 27mm??

have checked the shaft, it is about 27mm, is it the large bearings???.
TELL..

[TELL]

Re: indesit bearings

will check to day. dont things get easier as life goes on!!!!.
TELL..

[TELL]

Re: HOMARK GAS COOKER

cheers dave, i have looked all over on those sites and nothing comes up
for that model, helps me a lot, do you work off the manufacturers discs, or is there a site i can get the details, and any other m/c’s, like the bosch one, martin and gegsy put me onto the other day.
ta TELL..

[TELL]

Re: siemans w/dryer thermostats (drier stats)

cheers mate, just got it before of gegsy, on a previous enquiry.good site to use. is their any more like that?, i could use.
ta TELL..

[TELL]

Re: neff cooker door handle, pt no. please

cheers lads just got the info, great help, got part sorted with correct model,gegsy. martin good site, had been told about it ages ago off flyman, the old grey matter not working properly. its logged in favorites now.
ta TELL..

[TELL]

Re: still stuck with this indesit DI 620uk D/Washer.

thanks lads, not so confused on the contradicting timer/module fault codes iadom, and johnnyj, i think thats a definite on the module. there is a little diapragm with micro switched connected to circ/pump hose had that off, but found it very hard to operate, nearly blown my guts out to operate it. has that any bearing to it??. what is it??.
TELL..

[TELL]

Re: Sharp microwave shuts down every 59 seconds??

Ta lads, something to checkout,
TELL..

[TELL]

Re: proline cooker bottom element Pt/no please

ok dave, details on pm. for that element

by the way do you do the Homark range . need grill element for a
model -01-700401
0916HMGB61… (me thinks this is the model)
s/n 0040 12340
TELL..

[TELL]

Re: indesit dishwasher flashing light (fault code) non exist

cheers dave for the info, but thats the one i had used. this d/washer does not have a timer , it has the prog selector left hand top of door. i also checked out the heating element its ok.. its as soon it finishes the drain from the 1st initial rinse, then ready to fill again. thats when it shuts down. flashing the 3 neon. the model is a DI 620.
i did get a reading through the thermistor, but forget it now. it is situated top r/h corner of dispenser, then plugs into pcb, in conrol panel.
TELL

[Author]

Posts