[7390ROBERTS]

Re: Hotpoint CTD00P

Thanks for that info mate will be usefull to me. But I have since learned he has had it to peices himself so not going to do the job now I dont like it when that happens you never know what they have done could end up costing me money!! Thanks again helo and have a nice xmas

Cheers Rob

[7390ROBERTS]

Re: Hotpoint ultima D/F 32 p

Thanks petalpop will do that i have not seen the machine yet will check that first when i go tomoro.

Thanks again Rob

[7390ROBERTS]

Re: Whirlpool USA T/D Parts Required

Thanks John you are a gentleman I will go back tomoro and check the stat tomoro before i order parts.

thanks again John
Rob

[7390ROBERTS]

Re: Whirlpool USA T/D Parts Required

Hi John I had never been to one of these before it was a real mess of fluff That is reason cleaned motor etc also a little bit nosey i am like that. What made me think it was the resistor i cant get any reading on it at all. should it be C/C or am i barking up the wrong tree. Should 4 terminals be C/C on stat. Horizontal terminals were O/C is that where the fault lies. Appreciate your help Thanks
Rob

[7390ROBERTS]

Re: HOTPOINT WF240

Thanks for reply Iadom cleaned buttons there is damage to them causing them to stick in the customer is disabled so after reading other threads i am going to put new buttons on and test motor. I did not know that if motor problem it would not fill so i never checked motor on visit 😳 Am still new to this game and learning every day. I hope it is just motor brushes but when i tested insulation was ok

Thanks again for info Rob

[7390ROBERTS]

Re: Bosch wok 2001

Problem solved was an intermitent wiring fault on pump.

Thanks for help

Rob

[7390ROBERTS]

Re: Bosch wok 2001

Right Mate i will try that but she is away on holiday for few days will let you know the outcome.

thanks again Guys

Rob

[7390ROBERTS]

Re: Bosch wok 2001

Will do cheers Greg

Rob

[7390ROBERTS]

Re: Bosch wok 2001

Thanks for quick reply Greg checked all the pipes and pump was all clear could the PCB cause this error code or have i missed something.

Thanks Rob

[7390ROBERTS]

Re: Hoover Washer/Drier Worn heater casing. Part Obsolete

Thanks Guys for the ideas will go and try something on them lines will let you know what happens

CHEERS LADS ROB

[7390ROBERTS]

Re: Hoover Washer/Drier Worn heater casing. Part Obsolete

Thanks Dave For posting the part numbers for me I appreciate it. If anybody has the parts will they reply please.

ROB

[7390ROBERTS]

Re: Hoover Washer/Drier Worn heater casing. Part Obsolete

Thanks Mike I have been giving it some thought overnite and am thinking of fitting a spring on the bottom of the Element then when the casing is closed it should keep it tight only worry is will it get to hot and heat the spring to much. Or would it be do any harm to the element if i just wrapped wire round a part of it to secure it.
If anyone else has any ideas i would like to hear them.

Rob.

[7390ROBERTS]

Re: Hoover Washer/Drier Worn heater casing. Part Obsolete

The casing i am talking about is the cast air duct on the top of the machine
Is there any way i can secure the element to stop it rattling about

[7390ROBERTS]

Re: Crucader tumble dryer no heat

Thanks Mate I will go have another look at it tomoro the filter light is not on the reverse timer is working
Cheers Rob

[7390ROBERTS]

Re: Crucader tumble dryer no heat

Thanks Martin I checked the reverse timer it is OK also stats at back at heater take it to be front stats.
thanks Rob

[Author]

Posts