AJC_Dave

Forum Replies Created

Viewing 15 posts - 31 through 45 (of 89 total)
1 2 3 4 5 6
  • Author
    Posts
  • January 25, 2013 at 3:11 pm in reply to: Maytag AAV2200AGW #388604
    AJC_Dave
    Participant

    Re: Maytag AAV2200AGW

    Thanks Don

    I’ve got a feeling that I’m going to have to go back with a better pitch and try and sell a front loader instead.
    She’s got a swimming pool and a home cinema down stairs so maybe I should look at selling her a new matching dryer as well!!

    Dave

    January 25, 2013 at 2:11 pm in reply to: Maytag AAV2200AGW #388602
    AJC_Dave
    Participant

    Re: Maytag AAV2200AGW

    Are these big top loaders now a thing of the past? Most large machines seem to be front loaders now from what I can find. I’m a bit stuck with this one as she has a matching dryer beside it and I can’t budge her into having anything else at the moment.

    January 15, 2013 at 8:53 pm in reply to: Siemens WM16S796GB/03 #387897
    AJC_Dave
    Participant

    Re: Siemens WM16S796GB/03

    Apologies….just saw the part about the extra screws with the bearing set and thought it was a different washer.

    January 15, 2013 at 2:56 pm in reply to: Siemens WM16S796GB/03 #387894
    AJC_Dave
    Participant

    Re: Siemens WM16S796GB/03

    Not complicated at all. Top and front come off. Disconnect everything as normal including suspension legs. Drum out. The tub has some lugs around it which needs removing. I just knock them off with a cold chisel but you could cut them off with a dremel etc. The screws that come with the kit just slot into the spare holes when you put the tub back together. Never had to change a drum support on one but you will need to check it when you have it out. Dave

    January 15, 2013 at 11:32 am in reply to: Anyone breaking a Miele W/D endfame required #387813
    AJC_Dave
    Participant

    Re: Anyone breaking a Miele W/D endfame required

    Too many 9s… 07760616937

    January 15, 2013 at 8:14 am in reply to: Anyone breaking a Miele W/D endfame required #387811
    AJC_Dave
    Participant

    Re: Anyone breaking a Miele W/D endfame required

    If you get no luck give wastecare in Halifax a call on 077606169937. Can’t remember the name of the bloke but he’s quite helpful. They refurbish Bosch, Miele and John Lewis appliances for the most and hold plenty of spares. They have another place in Normanton near Castleford which may have one too. They only look for about £20 for a Bosch motor so shouldn’t be after much more for a Miele one especially if you are splitting it. Hope this helps…Dave

    January 10, 2013 at 9:10 pm in reply to: Baumatic BT2950SS Oven Element #387601
    AJC_Dave
    Participant

    Re: Baumatic BT2950SS Oven Element

    Thanks…

    January 10, 2013 at 5:17 pm in reply to: Miele G698-3 SC Plus – Valve #387586
    AJC_Dave
    Participant

    Re: Miele G698-3 SC Plus – Valve

    Only Miele parts I usually change are motor brushes and door seals which I get from connect. Never thought to check with them… thanks for the number. Dave

    January 10, 2013 at 1:26 pm in reply to: Miele G698-3 SC Plus – Valve #387584
    AJC_Dave
    Participant

    Re: Miele G698-3 SC Plus – Valve

    Thanks Don. Will order from Holland as there’s no panic getting it quickly.
    Thanks again..
    Dave

    January 7, 2013 at 3:55 pm in reply to: What’s happened to A.S.D Leeds? #387384
    AJC_Dave
    Participant

    Re: What’s happened to A.S.D Leeds?

    Hi mate
    As far as I’m aware, they went bust before Xmas. One of the lads that worked for them told me. Used to use them for whirlpool parts which were well priced…
    Dave

    January 5, 2013 at 9:44 pm in reply to: Indesit F06 Fault Code? #387301
    AJC_Dave
    Participant

    Re: Indesit F06 Fault Code?

    Brilliant……thanks!

    January 5, 2013 at 8:44 pm in reply to: Indesit F06 Fault Code? #387298
    AJC_Dave
    Participant

    Re: Indesit F06 Fault Code?

    It has N/A for F06?

    January 5, 2013 at 7:41 pm in reply to: Indesit F06 Fault Code? #387296
    AJC_Dave
    Participant

    Re: Indesit F06 Fault Code?

    I read that but thought it would be EVO2 which there is nothing.

    January 4, 2013 at 12:51 pm in reply to: CDA CI994 Control Panel/ Fascia #387113
    AJC_Dave
    Participant

    Re: CDA CI994 Control Panel/ Fascia

    Part number is 763738699 if anyone ever needs it. Seems to have a weak point where the door opening button is attached to the panel.

    December 21, 2012 at 10:41 am in reply to: Beko WM5001W #386345
    AJC_Dave
    Participant

    Re: Beko WM5001W

    Hi
    After it carrying out every function on test mode, I thought it had to be the pcb. Second visit, after PCB change not going to plan I tested the heater, motor and thought I’d checked the pressure switch. Went armed with a pressure switch this morning and it now works. Can’t identify a problem with the old one but will have another look at it tonight. The machine works now which I guess is the main thing.
    Thanks for all the input…
    Dave

  • Author
    Posts
Viewing 15 posts - 31 through 45 (of 89 total)
1 2 3 4 5 6