allan

Forum Replies Created

Viewing 15 posts - 181 through 195 (of 200 total)
1 2 3 … 12 13 14
  • Author
    Posts
  • January 20, 2007 at 6:50 am in reply to: Hotpoint condenser dryer ctd00p #201448
    allan
    Participant

    Re: Hotpoint condenser dryer ctd00p

    no have not changed switch, and it is a 2 stat machine
    Thanks

    January 19, 2007 at 10:28 pm in reply to: Hotpoint condenser dryer ctd00p #201445
    allan
    Participant

    Re: Hotpoint condenser dryer ctd00p

    thanks but tried that, wondered if this model had any kind of module?

    January 16, 2007 at 4:57 pm in reply to: wiring loom hotpoint wma33 #200658
    allan
    Participant

    Re: wiring loom hotpoint wma33

    Thanks 😳

    January 10, 2007 at 4:42 pm in reply to: creda reflection ?? #200225
    allan
    Participant

    Re: creda reflection ??

    Thats great, thank you so much
    Allan

    January 10, 2007 at 10:22 am in reply to: Hotpoint wma 33 no motor action #200015
    allan
    Participant

    Re: Hotpoint wma 33 no motor action

    Thanks Jim I will try that

    January 9, 2007 at 10:58 am in reply to: Hotpoint wma 33 no motor action #200013
    allan
    Participant

    Re: Hotpoint wma 33 no motor action

    checked harness so suspect module

    December 19, 2006 at 6:36 pm in reply to: Candy CNA166 #198337
    allan
    Participant

    Re: Candy CNA166

    Thanks for your help, all sorted now, seems it must have had a knock on the start/pause button which broke the switch of behind the panel on the circuit board, have managed to solder it back and all seems fine!!
    Thanks again Martin.

    December 19, 2006 at 4:58 pm in reply to: Candy CNA166 #198336
    allan
    Participant

    Re: Candy CNA166

    Yep tried that!?

    December 19, 2006 at 4:20 pm in reply to: Candy CNA166 #198334
    allan
    Participant

    Re: Candy CNA166

    Thanks for the list, but machine wont even allow me to set test cycle, its the door locked light and the stop light that are flashing not the ones used in the fault finding chart
    Allan

    October 29, 2006 at 7:24 pm in reply to: neff element part no please #193636
    allan
    Participant

    Re: neff element part no please

    Thanks very much for that Jackal much appreciated
    Regards Allan

    October 28, 2006 at 10:03 pm in reply to: neff element part no please #193632
    allan
    Participant

    Re: neff element part no please

    Hi and thanks for the reply I think it is 195 307 138 or it could be 133
    Thanks Allan

    August 9, 2006 at 11:29 am in reply to: Hotpoint dishwasher prob E05 #184337
    allan
    Participant

    Re: Hotpoint dishwasher prob E05

    Thanks for your help, customer just phoned to say it was not the right fault code no. has now put glasses on and reffered to the manual, found blocked filter!!!!!

    August 7, 2006 at 9:11 am in reply to: Hotpoint dishwasher prob E05 #184335
    allan
    Participant

    Thanks for the reply but no luck in the stickys

    June 3, 2006 at 9:10 am in reply to: Tricity Bendix AW1053W Fault #178062
    allan
    Participant

    what luck! found same motor in my store with tacho missing, but tried new motor with old tacho,
    perfect!
    Thanks Allan

    June 2, 2006 at 5:29 pm in reply to: Candy frost free help please #178235
    allan
    Participant

    No drain heater, but I wrapped a length of wire around the part of the heater above the drain and positioned it into the drain hole, hopefully this may help keep it clear?
    Thanks for your replys and help
    Allan

  • Author
    Posts
Viewing 15 posts - 181 through 195 (of 200 total)
1 2 3 … 12 13 14