allan

Forum Replies Created

Viewing 15 posts - 61 through 75 (of 200 total)
1 2 3 4 5 6 … 12 13 14
  • Author
    Posts
  • April 3, 2013 at 5:58 pm in reply to: Beko double oven timer #393090
    allan
    Participant

    Re: Beko double oven timer

    Thanks for the reply, have added one to my order.
    Cheers Allan

    February 17, 2013 at 9:48 pm in reply to: Parts breakdown for belling 335an #390368
    allan
    Participant

    Re: Parts breakdown for belling 335an

    Thanks, much appreciated
    Allan

    December 11, 2012 at 8:53 am in reply to: Aeg auto washer zero #386151
    allan
    Participant

    Re: Aeg auto washer zero

    Sorry :boops: the model is 74825 it starts to fill, then goes to zero will know a bit more when I’ve been along.
    Thanks Martin

    November 24, 2012 at 8:52 pm in reply to: Cata model no efg60ss2 #385308
    allan
    Participant

    Re: Cata model no efg60ss2

    Thanks jim, yes that’s the one, found the stat on top of oven open, failed because of power cut when oven was hot, next problem is getting the stat as my spares is quoting up to 10 days 🙁

    November 19, 2012 at 6:44 pm in reply to: Hotpoint stat hm3121 #385026
    allan
    Participant

    Re: Hotpoint stat hm3121

    Thanks for that
    Allan

    November 11, 2012 at 12:18 pm in reply to: Beko drcs68w water tank full #384573
    allan
    Participant

    Re: Beko drcs68w water tank full

    No, float switch ok cuts out when reservoir fill up and water full indicator comes on

    November 11, 2012 at 9:48 am in reply to: Beko drcs68w water tank full #384571
    allan
    Participant

    Re: Beko drcs68w water tank full

    Hi yes I have, no power to new pump, old pump was completely seized.

    August 14, 2012 at 5:33 pm in reply to: Smeg circulating pump dishwasher #379420
    allan
    Participant

    Re: Smeg circulating pump dishwasher

    Thanks

    August 1, 2012 at 4:07 pm in reply to: Zanussi built in cooker zdq895x cuts off #378018
    allan
    Participant

    Re: Zanussi built in cooker zdq895x cuts off

    Hi Tom Still waiting to go back, they are away for a while, did you have any joy, if its a board fault there no longer available!
    Allan

    April 20, 2012 at 9:53 am in reply to: Hob removal trinity bendix se558 #373562
    allan
    Participant

    Re: Hob removal trinity bendix se558

    Hi Martin sorry listed the wrong details, too many pads with details on! This is a Zanussi zkc6020w, two screw at back of hob and three under facia allow hob to be lifted but it is a complete unit with the controls incorporated into hob, wiring and oven stat dosent allow more than a couple of inches access, need access to a workshop manual to work out way to get at elements, sorry for the cock up I best cancel this post and realist this query
    Allan

    January 23, 2012 at 11:13 am in reply to: Hja8704 washer dryer #367664
    allan
    Participant

    Re: Hja8704 washer dryer

    Thanks, but still can’t work out which one of the ducts to fit?

    December 1, 2011 at 7:57 am in reply to: Hotpoint wml540p door seal #364617
    allan
    Participant

    Re: Hotpoint wml540p door seal

    Thanks for that Jim.

    November 29, 2011 at 4:19 pm in reply to: Temperature limiter Bosch hbn3550gb/02 #364526
    allan
    Participant

    Re: Temperature limiter Bosch hbn3550gb/02

    Thanks

    November 6, 2011 at 9:24 am in reply to: Help!! Thermostat creda cooker #363078
    allan
    Participant

    Re: Help!! Thermostat creda cooker

    That’s great thank you for your help, much appreciated
    Allan

    November 5, 2011 at 6:56 pm in reply to: Help!! Thermostat creda cooker #363075
    allan
    Participant

    Re: Help!! Thermostat creda cooker

    Yeah very expensive and special order, no patten available! Was hoping to find some old stock lol
    Allan

  • Author
    Posts
Viewing 15 posts - 61 through 75 (of 200 total)
1 2 3 4 5 6 … 12 13 14