allan

Forum Replies Created

Viewing 15 posts - 46 through 60 (of 200 total)
  • Author
    Posts
  • in reply to: Door interlock for indesit iwb71251 #429037
    allan
    Participant

    Re: Door interlock for indesit iwb71251

    Oh ok, was a bit worried the wiring would be different as the numbers not the connection plug aren’t the same

    in reply to: Distripart cd? #425253
    allan
    Participant

    Re: Distripart cd?

    Shame, do they do anything else?

    in reply to: Ise 2 motor brushes #424798
    allan
    Participant

    Re: Ise 2 motor brushes

    Thanks, found them through a vestel search came up as cbn9049.
    Allan

    in reply to: Ise 2 motor brushes #424796
    allan
    Participant

    Re: Ise 2 motor brushes

    Thanks, let’s hope some one can help.
    Allan

    in reply to: Hotpoint Tumble dryer bearing #424219
    allan
    Participant

    Re: Hotpoint Tumble dryer bearing

    Thanks for the help

    in reply to: Hotpoint Tumble dryer bearing #424217
    allan
    Participant

    Re: Hotpoint Tumble dryer bearing

    Luckily they stopped using it as the felt started to hang out, drum is still in good condition, so worth a punt if I can get the bearing felt, found the part number given on Qualtex so hope that the one! Any ideas as to gluing it in place or are the already sticky?

    in reply to: Hotpoint Tumble dryer bearing #424215
    allan
    Participant

    Re: Hotpoint Tumble dryer bearing

    Thanks at least it gives me a starting point

    in reply to: Bosch SGS46E02GB/75 dishwasher check water #415052
    allan
    Participant

    Re: Bosch SGS46E02GB/75 dishwasher check water

    Thanks will check that out when I go later today, Allan

    in reply to: Bosch SGS46E02GB/75 dishwasher check water #415050
    allan
    Participant

    Re: Bosch SGS46E02GB/75 dishwasher check water

    Is that to the right side of the water matrix? Thanks

    in reply to: Bosch field coil wrong way round? #407007
    allan
    Participant

    Re: Bosch field coil wrong way round?

    To be honest I normally mark them, was thinking that as it was Bosch with push in pins etc ,they would have made it impossible to get wrong! Won’t make same mistake again! Have refitted and luckily all seems ok, looked at amount of carbon in end frame and around field coil and matched the two! Anyway I was lucky.

    in reply to: Hotpoint c367ewh Facia #405346
    allan
    Participant

    Re: Hotpoint c367ewh Facia

    Thanks Kevin

    in reply to: Servis heater #403467
    allan
    Participant

    Re: Servis heater

    No one!

    in reply to: Cooling impeller Hotpoint ctd00 #402995
    allan
    Participant

    Re: Cooling impeller Hotpoint ctd00

    Thanks for that, can put it back together now 😀
    Allan

    in reply to: Beko cut out kit d533w #402382
    allan
    Participant

    Re: Beko cut out kit d533w

    Ok thanks, so you think I will need two kits in that case?

    in reply to: Hotpoint bwm129 built in door seal #398754
    allan
    Participant

    Re: Hotpoint bwm129 built in door seal

    Thanks for all your input, look like its going to be a fun job! Will savour every minute 🙁

Viewing 15 posts - 46 through 60 (of 200 total)