atech

Forum Replies Created

Viewing 15 posts - 16 through 30 (of 32 total)
1 2 3
  • Author
    Posts
  • December 31, 2010 at 12:12 pm in reply to: Baumatic BDW13 #339448
    atech
    Participant

    Re: Baumatic BDW13

    Thanks for the advise. I will check the pressure switch/system. HAPPY NEW YEAR 😀

    November 20, 2009 at 7:01 am in reply to: AEG santo 1688 TH7 #304223
    atech
    Participant

    Re: AEG santo 1688 TH7

    Sorry I posted in the wrong section

    December 20, 2008 at 8:30 pm in reply to: Hotpoint WD72 #272067
    atech
    Participant

    Re: Hotpoint WD72

    Thanks. Looks like the heater. 🙂

    December 19, 2008 at 11:53 pm in reply to: Hotpoint WD72 #272065
    atech
    Participant

    Re: Hotpoint WD72

    This machine goes through the wash. It shows E15 when it comes to the spin cycle

    December 19, 2008 at 6:07 pm in reply to: Hotpoint WD72 #272064
    atech
    Participant

    Re: Hotpoint WD72

    I’m going back on Monday. I will check it then.

    December 19, 2008 at 5:53 pm in reply to: Hotpoint WD72 #272062
    atech
    Participant

    Re: Hotpoint WD72

    I have done the wet test with cloths in and empty. The customer has not mentioned anything about it being nosiey

    December 19, 2008 at 5:41 pm in reply to: Hotpoint WD72 #272060
    atech
    Participant

    Re: Hotpoint WD72

    The drum goes around Ok. I have run a WET test. It does not spin in the WET test cycle. The machine get’s to the spin cycle and E15 comes up.

    November 27, 2008 at 3:26 pm in reply to: Hygena APM8513 #269597
    atech
    Participant

    Re: Hygena APM8513

    Yes, that’s the right module number, there’s a sticker down by the filter, with the motor, module, and various other part numbers. Saying there differant to the APM8512

    July 14, 2008 at 6:47 am in reply to: Hygena Dishwasher #257377
    atech
    Participant

    Re: Hygena Dishwasher

    Someone must know whats causing this fault. Come on Lads

    July 11, 2008 at 6:26 am in reply to: Hygena Dishwasher #257376
    atech
    Participant

    Re: Hygena Dishwasher

    Sorry. It’s an ADP 8132.

    April 30, 2008 at 1:19 pm in reply to: Brandt Dishwasher #250241
    atech
    Participant

    Re: Brandt Dishwasher

    Thanks. I’ll check the stat.

    August 25, 2007 at 12:34 am in reply to: Hpt WMA 10 #225043
    atech
    Participant

    Re: Hpt WMA 10

    Have you checked the door pecker? I have had a number of door lock faults and the door catch has been loose. IE there is not enough pressure on the door peg, to activate the interlock.

    August 25, 2007 at 12:22 am in reply to: Samsung SR-52028C Won’t switch back on! #225548
    atech
    Participant

    Re: Samsung SR-52028C Won’t switch back on!

    Have you tried banging the F/F to see if it wil restart? This wil normaly indicate a lose conection.

    August 25, 2007 at 12:20 am in reply to: Hotpoint 9525 pecker #225478
    atech
    Participant

    Re: Hotpoint 9525 pecker

    Some old hotpoints had a problem with the module! Is the module mounted on the back of the timer? If so it needs to be changed. It’s about 3″x3″? This caused the motor to go onto a spin, out of sequence.

    August 25, 2007 at 12:09 am in reply to: Hotpoint FFA97G Fridge Freezer Thermistors #225667
    atech
    Participant

    Re: Hotpoint FFA97G Fridge Freezer Thermistors

    Have you check the defrost heater? Is the drain hole blocked? Is there a defrost timer? Or is it controled from the board? I have had problems with Zanussi F/F, freezing up due to faulty timers and blocked drain holes. Hope this helps.

  • Author
    Posts
Viewing 15 posts - 16 through 30 (of 32 total)
1 2 3