atech

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 32 total)
1 2 3
  • Author
    Posts
  • March 21, 2019 at 3:10 pm in reply to: Bosch Condensing Drier #460930
    atech
    Participant

    Thank you. I’m now thinking that the customer might have pressed the wrong button by accident

    January 3, 2017 at 5:43 am in reply to: Candy GC4 1461 D1 #444161
    atech
    Participant

    Re: Candy GC4 1461 D1

    Thank you

    August 3, 2016 at 5:41 am in reply to: Electrolux EWX147410 #439811
    atech
    Participant

    Re: Electrolux EWX147410

    Thanks everyone

    August 1, 2016 at 4:40 am in reply to: Electrolux EWX147410 #439808
    atech
    Participant

    Re: Electrolux EWX147410

    Thanks. Would the drier element cause an intermittent fault like this is showing?

    May 27, 2015 at 5:39 am in reply to: Hoover VHD147a #427586
    atech
    Participant

    Re: Hoover VHD147a

    Fault code. The customer is in two minds whether to have it repaired, or to replace it. I ain’t going to spend too much time on this one, as I think it might be a waste of time. Just like to know what fault that lights 1,3 & 4 is.

    October 11, 2013 at 12:02 pm in reply to: Whirlpool AWO/D 4505 Srevice light #402603
    atech
    Participant

    Re: Whirlpool AWO/D 4505 Srevice light

    Carbons are ok, I suspect the motor is faulty.

    August 31, 2012 at 12:34 am in reply to: Indesit door boots in general #379618
    atech
    Participant

    Re: Indesit door boots in general

    I found that wedging a piece of wood from the packaging a WM comes in works. Now, you can either, cut a short length, about 5 inches, or just use the full length. With the short piece, I wedge it between the top of the door seal, and the inside of the machine, so the drum, is pushed tight to the back of the cabinet. If you use the long version, wedge it at the top, and rest the rest of the wood over you’re shoulder, pushing it in an upwards direction

    June 14, 2012 at 9:34 am in reply to: CNA Trading Appliance Ltd.Ceramic Hob #376448
    atech
    Participant

    Re: CNA Trading Appliance Ltd.Ceramic Hob

    I think I’ve got this sorted. It is the child lock

    June 14, 2012 at 4:41 am in reply to: CNA Trading Appliance Ltd.Ceramic Hob #376447
    atech
    Participant

    Re: CNA Trading Appliance Ltd.Ceramic Hob

    It could be. The problem is, all 4 are showing the “L” symbol. I have tried touching various symbols, but it dosn’t seem to make any difference.

    February 19, 2012 at 8:44 am in reply to: Tecnik TKL9060. Spares #369176
    atech
    Participant

    Re: Tecnik TKL9060. Spares

    Lovely. Thank you.

    January 4, 2012 at 6:47 am in reply to: Rangemaster #366475
    atech
    Participant

    Re: Rangemaster

    Thanks Chaps. I was thinking stat or timer.

    January 2, 2012 at 1:10 pm in reply to: Bosch WAE24126 UK/08 #366382
    atech
    Participant

    Re: Bosch WAE24126 UK/08

    No I didn’t. I haven’t come across this light sequence before.
    thanks. Mark.

    December 12, 2011 at 6:15 am in reply to: Diplomat ADM 8513 #365254
    atech
    Participant

    Re: Diplomat ADM 8513

    Ok thanks. I thnink they will proberbly change the machine.

    June 4, 2011 at 4:29 am in reply to: Diplomat HJA8552 #352664
    atech
    Participant

    Re: Diplomat HJA8552

    Yes it’s a Candy/Hoover. The light that comes on is the light next to the On & Door lock lights. So it’s the last light on the righthand side. It dosn’t flash. Solid light & pump

    May 21, 2011 at 3:40 pm in reply to: AEG date please #351925
    atech
    Participant

    Re: AEG date please

    Ok , thanks for that

  • Author
    Posts
Viewing 15 posts - 1 through 15 (of 32 total)
1 2 3