bradley

Forum Replies Created

Viewing 14 posts - 1 through 14 (of 14 total)
  • Author
    Posts
  • June 11, 2014 at 6:51 pm in reply to: HOTPOINT tumble dryers (the belt breaking bearing munchers) #415105
    bradley
    Participant

    Re: HOTPOINTtumble dryers (the belt breaking bearing muncher

    I reckon that the 1897 j3 is a stretch belt as fitted to the white knight dryers, and, if the idea works at all I will try to get the same belt with the appropriate ridges and treat myself to a life of ease.
    regards ian

    November 28, 2013 at 4:45 pm in reply to: rangemaster 110 simmersat #404973
    bradley
    Participant

    Re: rangemaster 110 simmersat

    no link wire involved then?

    November 28, 2013 at 11:56 am in reply to: rangemaster 110 simmersat #404971
    bradley
    Participant

    Re: rangemaster 110 simmersat

    there four wires to go on 4, but only one tag help please

    September 12, 2012 at 11:33 am in reply to: Diplomat Dishwasher FA #381020
    bradley
    Participant

    Re: Diplomat Dishwasher FA

    Thanks for advice. Customer has decided to scrap machine and buy a new one from us but I’ll remember for the future.

    March 6, 2012 at 2:37 pm in reply to: Hotpoint FDW20 leaking door #370367
    bradley
    Participant

    Re: Hotpoint FDW20 leaking door

    Thanks Martin but have just checked and it doesn’t appear to be split. Would it be obvious if it was? Anymore ideas?

    September 16, 2011 at 9:52 am in reply to: Indesit Moon SIXL145UK #359094
    bradley
    Participant

    Re: Indesit Moon SIXL145UK

    Thanks. 😀

    July 14, 2009 at 12:06 pm in reply to: zanussi digital display #290946
    bradley
    Participant

    Re: zanussi digital display

    Sorry about delay getting back. Thanks Martin. E-mail is robert.fletcher2@virgin.net

    July 3, 2009 at 9:28 am in reply to: Zanussi FJDR1466S E34 #290831
    bradley
    Participant

    Re: Zanussi FJDR1466S E34

    Thanks Martin. Will go back and check both.

    January 27, 2009 at 11:32 am in reply to: hotpoint WF740G display fault #275381
    bradley
    Participant

    Re: hotpoint WF740G display fault

    Thanks for getting back so quickly.
    Thought it would be.
    Are the boards pre-configured for this model or should I just tell her to get it repaired under the five year parts guarantee?

    November 18, 2008 at 3:19 pm in reply to: hotpoint BFi670 configure #267752
    bradley
    Participant

    Re: hotpoint BFi670 configure

    sorry boys .found out with electruepart/connections sent us the wrong board.after doing a part no enquiry!

    November 10, 2008 at 1:59 pm in reply to: hotpoint BFi670 configure #267749
    bradley
    Participant

    Re: hotpoint BFi670 configure

    i cannot c this edge connector.its a built in one.there r some wires that go 2 a thermister which hangs on the front of inner door.

    November 10, 2008 at 1:05 pm in reply to: hotpoint BFi670 configure #267746
    bradley
    Participant

    johnnyj wrote:Did you swap over the edge conector on the side of the timer, i’ve seen a few forget to do this and you will get a the test programe but will do nothing else, also when you fit the board to get it out of the test programe when the fill starts you cancel programe and it should be set for normal operation , hope this helps JJ

    this is a dishwasher and has no edge connector on board

    October 3, 2008 at 10:06 am in reply to: zwd1270w P.C.B. SET UP #263427
    bradley
    Participant

    Re: zwd1270w P.C.B. SET UP

    trickydickyd wrote:Did you find out why the board blew in the first place? Normally there’s a reason for them blowing. Water ingress, component fault, etc

    No after spending half a day on it. igave up and sold a new one. Bradley

    October 2, 2008 at 10:51 am in reply to: zwd1270w P.C.B. SET UP #263425
    bradley
    Participant

    Re: zwd1270w P.C.B. SET UP

    Yes the new board will need configuring…..I’ve sent you an email with that info attached

    Thanks Martin 4 info. board would not configure.looks like display gone also. cheers bradley

  • Author
    Posts
Viewing 14 posts - 1 through 14 (of 14 total)