Forum Replies Created
-
Posts
-
Re: Hello Everybody ..Ci555. small prob
Been retired , just waiting now for the other half to choose another machine , won’t be 500 quid job this time though 😉
Re: Hello Everybody ..Ci555. small prob
Have pulled out the control board just in case any damp is playing things up , but all dry
Its been unplugged since last night and was like this on first switch on today . and unplageed for the last coupl of hours .
Just considering chucking a 50 quid controller in as its the only complcated part 😉 ? or not ;
C.
Re: Hello Everybody ..Ci555. small prob
its already unlocked ans empty
Holding the Start/Pause/Cancel button does nothing.
All selections are in a correct position, have tried lots of other permutations .The moment the switched on and power button is pressed . the lighta go one in the sequence ..
Spin…… ready …. then the top 2 start flashing. . wierd .. with a set of bearings needed soon too, wondering if its time to retire it ? . pity as the rest is still in top nick
and its a good old washer..
ChrisRe: Hello Everybody ..Ci555. small prob
Soory for not coming back but until now the old banger has been performing ok ..
Until this morning .. upon switch on , its just got 2 lighs on and 2 flashing lights.
or
https://i.imgur.com/Jz2Aj2i.mp4
any clues ?
thanks in hope .. 😉
Chris
Re: Hello Everybody ..Ci555. small prob
Fitted a New Interlock and not improved it .
The machine finishes its cycle and stops , the interlock does not let the door open unless left for a long time, and the Ready Light does not re-illuminate as it has always done before ..
Does the 555 offer any error codes /diagnosis sequence ?On the verge of buying a new control board. 😮
ta
Chris
Re: Hello Everybody ..Ci555. small prob
sorted force used but not too much…
the interlock… what an over complicated thing..for what it does,.. :rolls:
C.Re: Hello Everybody ..Ci555. small prob
Back to the occasional Stuck Door . getting more and more often and now rather too often !
Did this last night, left for a long while and still stuck, unplugged and left all night and it opened this morning ok .But now after another wash it not opening again.
So Board or Door latch ? , seems the ready light doesn’t now come on when the machine is first switched on ( according to the Boss ! ) but will come on when the start/pause buton is pressed ! ..
So leaning towards a faulty control board ?
Any Clues guys ? , got a machine full of School clothes need for tomorrow !! ooer!!
ta.
ChrisRe: Hello Everybody ..Ci555. small prob
Removed post for the time being.. unless prob surfaces again. :rolls: .
C.Re: ISE 555 playing up again .
Flopped in this morning… 😀 ..
In and all going again so, more brownie points from the other half . 😆
Were a bit on the worn side .. :eeek:
sorry naff piccy from my old phone
C..
Re: ISE 555 playing up again .
Ordered last Friday, so weekends out probably, had email on Monday saying posted (2nd class )
Re: ISE 555 playing up again .
Hmm ,
just a week now since ordered the new brushes from the store and nothing appeared so far.. 🙁 ..
C.
Re: ISE 555 playing up again .
Element just been in a bucket and Heats up ok .
Off to find some brushes..
they looked ok When i did the bearing some weeks back .
But the ISE does have hard life…C
Re: ISE 555 was ok , So i thought!
All done, finished quiet and no leaks ..
Rear bearing disintegrated, couple of nearly square balls , and the cage as gone into a pile of swarf on the ground .?
byzz til next disaster .. 😀
C.
Re: ISE 555 was ok , So i thought!
yup my bad,,, Did get it off but didn’t half need a good hiding to get the shaft out.( did use another 8mm to take the pounding)
the Outer bearing has disintegrated, misshapen balls ooer!
the cage has disappeared completely 😯 ,so a bit of a mess all round , Spider seal surface is ok and smooth , just waiting for the bearings.
Oh !! and the slime inside .. 😉
C
