Forum Replies Created
-
Posts
-
Re: zanussi dishwasher error code AL5
Time out on fill (as per Penguin’s reply in the thread Martin linked to) 🙂
Dave.
Re: Cookers/Caremark Dishwasher 02-800473
Connect list the first two (and pictures) but no stock.
The third part isn’t recognised but you may not need it now I’ve seen a picture of the hinges on there.
Dave.
Re: Cookers/Caremark Dishwasher 02-800473
According to the Caremark disk it’s a Haier Bob 🙁
Left hinge articulation (their description) 012G9380558
Right hinge articulation – same but with 559 on the endAlso what is described as “complete hinge” (bar across bottom of door) is 120800589 but whether it includes the other two parts, the picture is cr@p 😕
Dave.
Re: AEG dw42300 dishwasher
Mains supressor has a hairline crack in it ?
I’ve had that a few times, also wiring chaffed in door loom …
Dave.
Re: play in belling oven door
It was the sockets in that case, they have to be fitted inside and a mod carried out (drill larger holes through cavity and new bolts etc).
If they fitted them incorrectly most people try and fit them as the original throught the front with the door off but it sounds like they did it correctly.
On the new hinge sockets there is a block on the outside, remove the lower bolt holding it and fit a washer in there and it may bring the door up to the seal, if that doesn’t work they’re a bit stuck I’m afraid as the hinges will be worn.
Dave.
Re: TECHNICS SPARES
It’s 0870 9099100
Why though Pinky ?
Technics are manufactured by Bosch, Fagor and Whirlpool on the whole 😉
Dave.
Re: play in belling oven door
Is it the hinges or the hinge sockets (more likely) they replaced ?
If they have, they will have fitted them wrong I expect.
The hinges themselves (kit) is now obsolete as are the springs.
Check the sockets though 😉
Dave.
Re: fuse creda
According to Partfinder it isn’t replaceable, if anyone knows the value though ? 😉
Dave.
Re: AEG L74630 AUTO CAUSING PROBLEMS.
On the way 🙂
If you don’t get them by later today let me know as large attachments seem to go astray from my email address at time.
Dave.
Re: Zanussi FS1155W
There you go then:
http://www.ukwhitegoods.co.uk/modules.p … 8243#68243
New addition 🙂
Dave.
Re: Known Error Codes
Zanussi Washing Machine Error Codes
Most models with the single control/display (EWM1000) PCB.
*Note* these are the engineer codes displayed after entering the configuration/diagnostics mode.
To enter diagnostics:
1. Switch off the appliance.
2. Press and hold down START/PAUSE and any one of the option buttons simultaneously.
3. Holding down both buttons, switch the appliance on by turning the programme selector one position to
the right (clockwise).
4. Continue to hold down the START/PAUSE and option buttons until the LED begins to flash (at least 2
seconds).In the first selector position, the operation of the buttons and the relative LEDs is checked; turning the
selector knob clockwise activates the diagnostics cycle for the operation of the various components and
displays any alarm conditions.E11: Difficulty in filling during wash phase
E13: Water leakage.
E21: Difficulties in draining .
E22: Possibly blocked condensor or ntc fault.
E23: Malfunction of drain pump triac.
E24: «sensing» circuit of the component (triac) that controls the drain pump faulty
E33: Incongruence between closure of anti-boiling and 1st level contacts of pressure switch
E35: Water level too high
E36: «sensing» circuit of anti-boiling pressure switch faulty
E37: «sensing» circuit of 1st level pressure switch faulty
E39: “HV” «sensing» circuit of anti-overflow pressure switch faulty
E40: Door open, Interlock, wiring or main PCB
E41: Door open
E41: Problems with aperture of door
E42: Problems with aperture of the door
E42: Problems with aperture of the door
E43: Problems with the triac which actions the door interlock
E43: Problems with the triac which actions the door interlock
E44: Door closure «sensing» circuit faulty
E45: Problems with the «sensing» circuit of the triac that actions the door interlock
E51: Motor power triac short-circuited
E52: No signal from the motor tachymetric genetaror
E52: No signal from the tachymetric generator
Procedure for checking commutator motors
E53: Problems with the «sensing» circuit of the triac which powers the motor
E54: Motor relay contacts sticking
E61: Insufficient heating during washing
E62: Overheating during washing
E66: The contacts of the heating element power relay are always closed
E71: NTC washing sensor faulty.
E82: Error in reading the RESET/OFF position of the programme selector.
E83: Error in reading the programme selector code
E93: Incorrect machine configuration.
E94: Incorrect configuration of washing cycle
E95: Communications error between microprocessor and the EEPROM
E96: Incongruence between control panel version and configuration data
E97: Incongruence between selector version and configuration data
EA1: Drum positioning system (DSP) faulty (top-loaders only)
EB1: Incorrect mains frequency
EB2: Mains voltage too high
EB3: Mains voltage too lowRe: bosch maxx wil 2260 problem
The tray probably just needs a good clean out as the syphon for the additive will easily block especially if it is overdosed.
Dave.
