DDDave

Forum Replies Created

Viewing 15 posts - 181 through 195 (of 212 total)
1 2 3 … 12 13 14 15
  • Author
    Posts
  • April 15, 2009 at 10:23 pm in reply to: Hotpoint WF210 #283274
    DDDave
    Participant

    helo_75 wrote:including no earth in plug, reverse polarity, down to earth heater, etc

    Earth is working. Polarity has not been changed in sockets ,if the element was faulty then why would it work in the workshop ???
    Thanks for the suggestions.
    Any more PLEASE ??

    March 23, 2009 at 2:02 pm in reply to: Board repairs #281026
    DDDave
    Participant

    Thanks Martin

    March 11, 2009 at 1:53 pm in reply to: Powerpoint TW36FI #279848
    DDDave
    Participant

    Re: Powerpoint TW36FI

    DDDave wrote:

    Penguin45 wrote:
    Powerpoint = Irish Haeir……. 1st four is flooded base.

    Chris.
    Thanks Chris.
    The base id dry and the switch and float are ok.

    Sorry. That should read “The base is dry and the switch and float are ok”
    Any other ideas ??

    March 11, 2009 at 7:37 am in reply to: Powerpoint TW36FI #279846
    DDDave
    Participant

    Re: Powerpoint TW36FI

    Penguin45 wrote:Powerpoint = Irish Haeir……. 1st four is flooded base.

    Chris.
    Thanks Chris.
    The base id dry and the switch and float are ok.

    February 18, 2009 at 8:44 pm in reply to: Another Zanussi. ZWF1431S #277620
    DDDave
    Participant

    Re: Another Zanussi. ZWF1431S

    Martin wrote:Check your email Dave. 😀

    Email received.
    Thanks very much Martin, I will test it tomorrow.

    February 18, 2009 at 1:04 pm in reply to: Another Zanussi. ZWF1431S #277618
    DDDave
    Participant

    Re: Another Zanussi. ZWF1431S

    Martin wrote:

    DDDave wrote:
    Thank you. PM sent

    But no PM received. 😕
    Tried again

    February 18, 2009 at 12:36 am in reply to: Another Zanussi. ZWF1431S #277616
    DDDave
    Participant

    Re: Another Zanussi. ZWF1431S

    sparepart wrote:take the board out and check it closely , I’ve got a Zwf1430w that i’m doin at mo , and I had to look closely with a magnifying glass to find it , there are two boards available on exxy at mo , part numbers 97391451756014 and 973914601126001 £15 each brand new , sadly not what I want …….but I suspect fault is board ……Regards Alan

    Thanks , I did that but could not find any faults.

    February 18, 2009 at 12:34 am in reply to: Another Zanussi. ZWF1431S #277615
    DDDave
    Participant

    Re: Another Zanussi. ZWF1431S

    Martin wrote:Go into ‘diagnostics mode’ to check last error reported. If you need info on how to do that then pm me your email address. (Remind me of model number when you do though) 😉

    Thank you. PM sent

    January 14, 2009 at 1:26 pm in reply to: HP DWF33 no wash #273841
    DDDave
    Participant

    Martin wrote:
    You see the diverter allows the wash water to be circulated alternately between top and bottom spray arms but NOT together. The reason being is the machine only fills with a limited amount of water and not enough for both to operate at the same time.

    I didnt realise that. Thanks again.

    January 14, 2009 at 12:35 pm in reply to: HP DWF33 no wash #273839
    DDDave
    Participant

    Out of interest, would there be anything wrong with removing the diverter ?? When does it divert and to /from what ?

    January 13, 2009 at 9:40 pm in reply to: Miele T510 Dryer #273843
    DDDave
    Participant

    Thanks Chezza I will give that a try.

    January 13, 2009 at 9:37 pm in reply to: HP DWF33 no wash #273838
    DDDave
    Participant

    Thanks Martin

    November 30, 2008 at 10:57 am in reply to: Wascator interlock #270176
    DDDave
    Participant

    Re: Wascator interlock

    Will do. Thank you.

    November 29, 2008 at 7:00 pm in reply to: Wascator interlock #270174
    DDDave
    Participant

    Thank you Eddie. I will search it later
    Cheers
    Dave

    October 24, 2008 at 12:28 pm in reply to: Zan and Bendix wiring #266383
    DDDave
    Participant

    Re: Zan and Bendix wiring

    Thanks guys. I am in Ireland and the agent here said the loom was not available. I will contact Distriparts and order.
    Thanks again.

  • Author
    Posts
Viewing 15 posts - 181 through 195 (of 212 total)
1 2 3 … 12 13 14 15