DRH

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 48 total)
1 2 3 4
  • Author
    Posts
  • September 24, 2014 at 2:35 pm in reply to: bosch wvt12842gb #419556
    DRH
    Participant

    Re: bosch wvt12842gb

    will give it a try.many thanks 😀

    October 25, 2013 at 12:33 pm in reply to: 3rlsq8033sw2 whirlpool #403245
    DRH
    Participant

    Re: 3rlsq8033sw2 whirlpool

    thanks Graham.any idea about the small electronic up in the facia ?. has that anything to do with drive.

    October 22, 2013 at 3:19 pm in reply to: Bosch WBB24759 washing machine #403228
    DRH
    Participant

    Re: Bosch WBB24759 washing machine

    could it be a preasure fault?

    October 22, 2013 at 3:06 pm in reply to: 3rlsq8033sw2 whirlpool #403243
    DRH
    Participant

    Re: 3rlsq8033sw2 whirlpool

    gearbox is free, you can turn it by hand.The motor runs slow taken off the gearbox.

    September 11, 2013 at 10:49 am in reply to: neff u1644n0gb/01 oven #400857
    DRH
    Participant

    Re: neff u1644n0gb/01 oven

    Many thanks Martin.

    July 25, 2013 at 12:22 pm in reply to: Siemens Oven ER15 #264837
    DRH
    Participant

    Re: Siemens Oven ER15

    hello have same fault, any help please. thanks

    July 25, 2013 at 12:09 pm in reply to: siemens er15 lock out #398191
    DRH
    Participant

    Re: siemens er15 lock out

    i got the door open. need a new lock now? just need to clear the error code.

    July 25, 2013 at 12:03 pm in reply to: Miele W1613 #397884
    DRH
    Participant

    Re: Miele W1613

    take the lid off,soapdraw out,facia will lift out of the way. two screws on top of front edge, screw under door seal.thats all there is to it.

    July 21, 2011 at 4:15 pm in reply to: Miele Washing Machine Error #355884
    DRH
    Participant

    Re: Miele Washing Machine Error

    The demonstration mode is active. its a poss?

    March 29, 2011 at 3:56 pm in reply to: Siemens wtxl720cgb/01 dryer #348108
    DRH
    Participant

    Re: Siemens wtxl720cgb/01 dryer

    it had a new module because the dryer was dead. has been fine since.from the start the dryer dose not heat at all. change prog and it then works fine.its a clean well looked after dryer. all filters fine.all connections on heater and mod all good.on the heater is a stat and a temp limiter, sorry for limited info martin.and thanks

    February 10, 2011 at 12:25 pm in reply to: Miele Dishwasher G674SC #344104
    DRH
    Participant

    Re: Miele Dishwasher G674SC

    poss heater preasure switch, just by wash pump.

    November 4, 2010 at 1:15 pm in reply to: hoover dyn10146p washer #334967
    DRH
    Participant

    Re: hoover dyn10146p washer

    many thanks.

    October 21, 2010 at 12:23 pm in reply to: Zanussi zwd1681w #333436
    DRH
    Participant

    Re: Zanussi zwd1681w

    leavemetogetonwithit
    many thanks. duff wire, bad connection. gave it a kick?
    it now works. I like my job today 😀

    October 20, 2010 at 3:44 pm in reply to: Zanussi zwd1681w #333434
    DRH
    Participant

    Re: Zanussi zwd1681w

    i hate washers 😥

    September 16, 2010 at 12:46 pm in reply to: whirlpool awz480e dryer. #330449
    DRH
    Participant

    Re: whirlpool awz480e dryer.

    no its in a large vets. told them to leave well alone until end of prog. its on its third set in about 10 days now.poor old dom/gen.

  • Author
    Posts
Viewing 15 posts - 1 through 15 (of 48 total)
1 2 3 4