[garn]

Re: Help My Washing Machine Is trying TO Get Out OF the Cupb

Hi Hotpoint
IV Already Made The Plinth Out OF Board Tape rd IT 0 TO 16{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d}. Going TO Fix Him To The Floor It Needs A couple OF Feet
paul 😉

[garn]

Re: Help My Washing Machine Is trying TO Get Out OF the Cupb

Evening Chris Thanks For Getting Back To me.
IV Had Productive Day Didn’T Get IN Til 750pm 🙂
The Appliance is A.
Smeg WD.12C. sn 4062 6 02440. 1200 rpm. Type 22052.

I Will Need TO New Smeg Front Feet For IT. Plus Four New Rubber Shocks Like The WRPO shock Pads .

The Floor Is Made Of A Smooth Tiles. But Its 16mm out of level Just On The Depth Between The Distance Of The Front And Rear Feet. The Whole Room is 500mm Out OF Level.
Its The is Located In The Basement In Victorian House Listed Building The Floor cant Be Changed :!:.

Thanks Paul.

[garn]

Re: Semens Dishwasher

Thanks Mate.
The ENr no Is SE 46A630GB/46 I Spot ed This Thought It Was Just the Serial Number :rolls:
Just Had A Load OF parts Delivered This Morning. should have Posted The Inquiry Yesterday. :rolls: IL learn It Will have TO Wait Know :P.
mp £4.10.
Thanks Jim Your On The ball 😉
PAUL… 🙂

[garn]

Re: new appliances hot&cold fill

Thanks For All The Input I Will Relay the Info To My Customer.
Who Keeps Filling His Service Washing Machine With A Hose pipe From His Hot Water Tank To Make IT Wash Quicker 😕
paul… 🙂

[garn]

Re: get one

WELL THIS SOUNDS LIKE THE SAME GUY THATS BEEN PHONING ME EVAN ON A SUNDAY AND IS ABOUT 200 MILES AWAY.
I DONT SUPPLY ISE APPLIANCES YET!
I RESANTLY TOOK A MONTHLY ADVERTISING CAMPAIN OUT IN THE CARMARTHEN JORNAL.
WITH THE RECYCLEING LOGO SAYING IT DOESEN”T COST THE EARTH TO REPAIR YOUR APPLIANCE.
HE WANTED TO KNOW THE FULL SPEC OF EVERY APPLIANCE THAT IS MADE BUT WAS VERY KEEN ON THE ISE.10 TIMES HE PHONED ME.
I PHONED MY LOCAL PAPER AND THAY SAID IT IS AVAILABLE AS FAR AS NEWTOWN AND CHESTER.
IN THE END I TOLD HIM TO CALL AND VIEW ONE .HE NEVER PHONED BACK AFTER THAT. :rolls: IT SOUNDS LIKE THE SAME GUY :rolls:

[garn]

Re: new appliances hot&cold fill

i know martin
its difficult to get them to part with there hpt 9934
there appliances are in excellent condition.
i change the bearings every 7 years and the odd backplate
tightening down all those bolts these days is a hell of a job im 50 the customer is about 90 and nothing is giving up due to constant boiling water.
iv got one customer who resulted in topping a service washing machine up with hot water because the programs are taking to long to wash.
they got rid of it and bought a wm63 of me. 😆
thank s for the input ukwg is a godsend 😀
paul… 😉

[garn]

Re: new appliances hot&cold fill

Penguin45 wrote:Um……. No. Invite your customers to join the 21st Century. Unless the boiler is directly over the washing machine, it will finish filling before the water even comes down the hot pipes. Educate them.

Chris.
thanks for the reply iv been telling them this .
the trouble is a lot of my customers have been ripping there oil boilers out. and gone back to coal because of the cost on fuel I’m going to change myself i spent £1200 over the past year on oil. calor gas in a tank could be as much as £2800 a year to run.
and I’m inundated with calls for these appliances 😮
if the recession keeps up we will end up making our own quality steel again and digging our own coal again.
http://www.welshcoalmines.co.uk/Carm/great_mou … lliery.htm –
regards a gwendraeth vally boy 😀
paul 🙂

[garn]

Re: CREDA CONSEPT C561EW PART NO?

Martin wrote:HI MARTIN HEAR 😉

Main Oven Selector Switch = C00228876
Main Oven Thermostat = C00231795
Service Manual = C00220990

Take a look on Connect to be sure those are the parts you need first won’t you? 🙂

hi mate no parts in connect

this appliance apparently theres no main oven heat or side heat and no fan.? any ideas 😥

[garn]

Re: HOVER MEGA VHC 392T

THANKS MATE
THE PUMP IS AN ASKOL -TWT
HAVE IT ON THE VAN 😛
JUST SAVED ME A 45 MILE ROUND TRIP 😆

THANKS PAUL…

[garn]

Re: Hotpoint TDC60 tumble dryer puts out no heat

iadom wrote:Methinks you are getting a little confused Garn. This machine is a TDC not a CTD.

The TDC does not have a pump, the CTD does not have the green spot stats or a dryness module.

The bearings are less likely to fail as the TDC has proper jockey pulleys and does not need a full V4 repair kit if the rear bearing does fail.

Jim. soz mate i think i have snow blindness to yearly in the morning 4me.anotherday off its belting down hear

[garn]

Re: Hotpoint TDC60 tumble dryer puts out no heat

been out and done a few of these recently
green spot stat gone dryness module buzzing clicking
done the job had a call back 4months later green stat gone again.
module OK.
i would recommend inspection of the float & pump chambers especially if the appliance is up to 3to4 years old the chamber may need cleaning
bit of a job while your at it check the bearings as well it may be worth putting a v4kit on it the same time
and delint the appliance hence it be OK for another to years

[garn]

Re: Bearing Shell Removal Tool – Now Available

over the past 38years iv had to make my own special tools or adapt others.
remember the old hpt drum locking tool
one wrong move and your skin is in pieces”
iv made few of these over time and supplied them to several brother engineers 🙂
this one saves your skin and bending round the drum to hold it. also adapts to10mm punch with a 2lb hammer strike .
those bearings come flying out even knock the race out if its stuck.

garn 😆

[garn]

Re: tricty bendix town&country

Penguin45 wrote:THIS is what you want.

Get surfaces spotless and weight dowm for 24 hours to achieve a bond.

Penguin45.

thanks again mate coudnt see it in m parts. 🙂

paul. 8)

[garn]

Re: Bearing Shell Removal Tool – Now Available

hi
just this week iv been out looking at some hydraulic press
for bearing removal what iv seen is to narrow to to get the drums in line.
looking at it these preses are usually used for motor car hub bearings
it could certainly be adapted. if one of these have been designed and made? it would be great.
iv have been thinking of purchasing a 18v cordless impact driver seen it working to do the job” especially with the wma bearing tool 2edition
to many bits with it
mind you this new one looks value for money

[garn]

Re: Amica appliances

your rite not a welded drum
I SPOKE TO GUY CALLED SIMON FREEAR OF AMICA INTERNATIONL
THE
OTHER DAY AND HE SAID THAT D&G ARE COVERING THE WARRENTY WORK.
THER IS NO WARRENTY INFOMATION IN THE IN THE PACK THAT COMES WITH THE APPLIANCE.
GOOD NEWS I HAVE A COPY OF THE WARRETY INFORMATION PACK FOR AMICA UK
ITS A CASE OF JUST PRINTING OF AND POP IT IN THE IMFOMATION PACK
THE IS NO REGISTRATION SERVICE WITH AMICA IT A CASE OF THE CUSTOMER PRODUSE A RECIET.
ANY ONE NEED A COPY EMAIL ME .
PAUL

[Author]

Posts