Forum Replies Created
-
Posts
-
Re: NEFF S4443b8GB SEMI INT DISHWASHER
Do any of these flash ? “Ready”,”Active” or “End”
Worth checking for earth leakage aswell, makes weird and wonderful faults with these electronic appliances :rolls:Greg
Re: NEFF B1641S2GB/01
Hi
The 50 deg is the start temp (which can be incremented) and when the temp is reached, the oC indicator in display will extinguisch IIRC.
If the TOC checks out then its looking like an PTC out of tolerance or more likely the module IMHO 😥Greg
Re: Still no heat
Most of the guys on here are “private” or self employed. If you use the engineer link to repairs@ then you will be getting a qualified professional to work on your appliance 😀
Hope that clears that up.
Greg
Re: Free energy
Well, Siemens are giving you up to 5 years FREE electric (in a roundabout way) when you buy one of their fridge freezers 😀
http://www.siemensappliances.co.uk/Greg
Re: Bosch Exxcel Tumble Drier not heating
Hi
Fault code is not recognised 😕 but the reset is on top of heater unit after you have removed the rear panel.Power off before attempting :plug:
Greg
Re: i would appreciate work in postcodes l, wn, wa
Hi Mike
Have you considered joining repairs@.Regards
GregRe: Known Error Codes
Hotpoint Error Codes
From the Hotpoint website, a step in the right direction in all fairness.
Early Hotpoint Washing Machines and Washer Dryers
F10 – No cold fill. Check that the taps are on or if the drain hoses are kinked.
F11 – No hot fill.The ambient temperature is likely to be below freezing possibly due to the pipes being frozen. Also check that the taps are on or if the drain hoses are kinked.
F12 – No mixed fill. It is likely that the water is not turned on at the taps.
F13 – Check the water supply, inlet valve and hot and cold hose connections.
F14 – A fault with the water heating has occurred. Book a service engineer
F15 – Water is not being pumped out and a flood condition could occur. Check that the drainage hose is raised to the recommended minimum height and that the pipe is not blocked.
F16 – Extremely high water level Disconnect or turn off the water supply and ensure that the water level does not rise any more. Then Book a service engineer.
F17 – Door not closed properly. Close door firmly at the 3 o’clock position.
F20/1 – The thermistor resistance has drifted or the temperature scanning sequence is incorrect. The ambient temperature could be below freezing. Book a service engineer.
F30/31 – A motor drive problem has occurred. Try running the programme again. If the problem persists book a service engineer.
F40 – Water below protection level during a heat step. Book a service engineer.
F41 – Water level detect sequence incorrect. Book a service engineer.
F50/51 – Customer language and wash programme have not been saved. The system will run with default conditions (1000rpm max and English language). Book a service engineer to re-programme your product.Fault codes for LCD EVO1 Washing Machines and Washer Dryers
F01 – Short circuit motor triac – Book a service engineer.
F02 – Motor jammed tacho detached – Book a service engineer.
F03 – Wash thermistor open/short circuit – Book a service engineer.
F04 – Pressure switch jammed on empty – Book a service engineer.
F05 – Pressure switch jammed on full – Book a service engineer.
F06 – Program selector error – Book a service engineer.
F07 – Heater relay stuck – Book a service engineer.
F08 – Heater relay cannot be activated – Book a service engineer.
F09 – Incompatible eeprom – Book a service engineer.
F10 – Pressure switch not sensing correctly – Book a service engineer.
F11 – Pump cannot be activated – Book a service engineer.
F12 – Communication error – Book a service engineer.
F13 – Dryer fan or dryer thermisotor faulty – Book a service engineer.
F14 – Dryer element faulty – Book a service engineer.
F15 – Dryer element relay faulty – Book a service engineer.
H20 – Not fillings. Check tap, hose and inlet valves
LOCKED – Check interlock – Book a service engineer.Fault codes for LCD EVO2 and V4 Washing Machines and Washer Dryers
F01 – Motor traic short circuit – Book a service engineer.
F02 – Motor jammed or tacho detached – Book a service engineer.
F03 – Wash thermistor open/short circuit – Book a service engineer.
F04 – Pressure switch jammed on empty – Book a service engineer.
F05 – Pressure switch jammed on full – Check pump for blackages.
F07 – Heater relay stuck – Book a service engineer.
F08 – Heater relay stuck – Book a service engineer.
F09 – Setup error – Book a service engineer.
F10 – Pressure switch not sensing – Book a service engineer.
F11 – Pump cannot be activated – Book a service engineer.
F12 – No communication between cards – Book a service engineer.
F13 – Drying thermistor open/short circuit – Book a service engineer.
F14 – Drying element faulty – Book a service engineer.
F15 – Dryer element relay fault – Book a service engineer.
F17 – Interlock error – Book a service engineer.
F18 – Communication error – Book a service engineer.
H20 – Not filling. Check tap, hose and inlet valvesRefrigerators
F1 – Freezer thermistor open circuit. Book a service engineer.
F2 – Freezer thermistor short circuit. Book a service engineer.
F3 – Fridge thermistor open circuit. Book a service engineer.
F4 – Fridge thermistor short circuit. Book a service engineer.
F7 – Evaporator thermistor open circuit. Book a service engineer.
F8 – Evaporator thermistor short circuit. Book a service engineer.
F9 – Temperature set switch open circuit Book a service engineer.
FA – No feedback from Baffle Book a service engineer.
FB – Fridge Baffle motor operating continuously. Book a service engineer.
FE – Defrost time out. Book a service engineer.Dishwashers
F10 – Fill or empty time out. Check that the hoses are not kinked, that the taps are on or whether the drain pump or hose is blocked.
F11 – Heater timed out. The heater has not reached the required level. Book a service engineer.
F20 – Temperature under range. Book a service engineer. .
F21 – Temperature over range. Book a service engineer.
Fault codes for LCD Dishwasher Models
A01 – Float switch operated – Book a service engineer.
A02 – Open/Short circuit heater relay – Book a service engineer.
A03 – Short circuit on thermistor – Book a service engineer.
A04 – Unable to reach or sense temperature within 70 minutes – Book service engineer.
A05 – Pressure switch has not been reset – Book a service engineer.
A07 – Open/Short circuit wash motor triac – Book a service engineer.
A08 – Open/Short circuit auxiliary wash motor triac – Book a service engineer.
A09 – Open/Short circuit with main wash traic – Book a service engineer.
A10 – Open/Short circuit fill valve traic – Book a service engineer.
A11 – Half load valve traic or alternating motor action – Book a service engineer.
A12 – Open circuit heater rely – Book a service engineer.
A13 – Open/Short circuit dispenser traic – Book a service engineer.
A14 – Drain hose too low causing syphoning. Check drain hose and re-adjust.
H20 – Check tap and pressure of incoming water.Tumble Dryers
F1 – The level of required dryness has not been reached within the time period. Check that the correct programme has been selected
F2 – Thermistor or sensing circuit failure. Book a service engineer.
F3 – Heater plate over temperature. Check the filter and vent hose for a possible blockage.
Fault codes for LCD Tumble Dryers
F01 – Short circuit motor traic – Book a service engineer.
F02 – Motor jammed or fan blocked – Book a service engineer.
F03 – Front thermistor open/short circuit – Book a service engineer.
F04 – No pump piloting – Book a service engineer.
F05 – No feedback from the pump – Book a service engineer.
F08 – Static heater relay with contact welded closed – Book a service engineer.
F09 – Eeprom is not programmed or not functioning – Book a service engineer.
F10 – Common of heater open or one shot open – Book a service engineer.
F11 – No pump connection – Book a service engineer.
F12 – Communication error between boards – Book a service engineer.
F13 – Rear thermistor open/short circuit – Book a service engineer.
F15 – Dynamic heater relay with contact welded closed – Book a service engineer.
F-17 – Master relay welded closed – Book a service engineer.Obviously ignore the book an engineer bit 😉
Greg
Re: Spam
At least something good came from it. Have PMd and aplogised and also shown him link to the Instruction Manual thread 😀
Greg
Re: Spam
In Washing Machine & Dryers Help & Support Forum
organism wrote:HOOVER instruction manuals can be obtained in pdf format by calling this number: 01204 556 111 and quoting model and serial number of machine.
email is stuart.monkcom@liverpool.gov.uk 😕
Deleted anyway 😉Greg
