gegsy

Forum Replies Created

Viewing 15 posts - 6,406 through 6,420 (of 6,724 total)
  • Author
    Posts
  • in reply to: Indesit Circulation Pump – Motor – Capacitor? #149071
    gegsy
    Participant

    Re: Indesit Circulation Pump – Motor – Capacitor?

    Debris within the pump assembly jamming the impeller a possibilty.
    Failing that just change the capacitor app £10, if no cure most likely the motor.
    As always :plug: before attempting any repair.
    Greg

    in reply to: Bosch WFF2000 PreWash Light Flashing (again…) #149005
    gegsy
    Participant

    Re: Bosch WFF2000 PreWash Light Flashing (again…)

    3 flashes is indeed a pump fault or empty fault.

    Greg

    in reply to: Bosch WFF2000 PreWash Light Flashing (again…) #149003
    gegsy
    Participant

    Re: Bosch WFF2000 PreWash Light Flashing (again…)

    Sorry Martin part no change, 141120 is replaced by 143994 🙂

    in reply to: Servis rainwave 1100 #149054
    gegsy
    Participant

    Re: Servis rainwave 1100

    No problem Andy.

    Greg 🙂

    in reply to: 3 Million+ #149023
    gegsy
    Participant

    Re: 3 Million+

    :tup:

    in reply to: Bosch WFF2000 PreWash Light Flashing (again…) #149001
    gegsy
    Participant

    Re: Bosch WFF2000 PreWash Light Flashing (again…)

    drain pump part no – 143994 – £44.20 GBP

    Greg

    As always :plug: pull the plug before attempting any repair.

    in reply to: zan, BLOWING PUMPS #147659
    gegsy
    Participant

    Re: zan, BLOWING PUMPS

    Common prob Ive had with this fault has been the breather hose situated at the top of the tank connecting to dispenser. These either come adrift or just split thus causing wash water to run down tank and find a way onto empty pump.

    Greg

    in reply to: Servis rainwave 1100 #149052
    gegsy
    Participant

    Re: Servis rainwave 1100

    Appliance will only dry “half” the load, forget jeans and bulky items for starters.
    Off the top of my head there are 2 dry locations on the main timer.
    one is the dot after normal wash spin; the other is the same after delicate spin.
    For the dryer to function in either setting you will need to make sure the “half load” button is depressed and that a dry time has been set on dryer timer. Obviously door shut and switched on.
    Dont expect the same dry times as a standard full size dedicated tumble or condenser dryer.

    Hope that helps

    Greg

    PS make sure you allow the 10 mins cool down at the end of the dry cycle or you will most likely make the thermal protection thermostat activate.

    in reply to: Zanussi washer FJ1033 – flooding problem #148980
    gegsy
    Participant

    Re: Zanussi washer FJ1033 – flooding problem

    Sorry yes I know its stating the obvious but we have to tell you to do that.

    So please :plug:

    Greg

    in reply to: Recommended Listening #136073
    gegsy
    Participant

    Re: Recommended Listening

    Bowling for Soup. Someone said I resemble the large guitarist….. sods 😆

    in reply to: Zanussi washer FJ1033 – flooding problem #148978
    gegsy
    Participant

    Re: Zanussi washer FJ1033 – flooding problem

    Look for star washer on floor locate loose tacho slot it back in rear of motor, smack the star shaped retainer back in behind tacho unit and adhere it in place.

    Greg

    in reply to: Bosch SGS43A12GB/27 dishwasher. #148800
    gegsy
    Participant

    Re: Bosch SGS43A12GB/27 dishwasher.

    The diverter lets you choose to have a half load or full load; switching between top and bottom spray arm feeds when selected.

    Greg

    in reply to: Bosch SGS43A12GB/27 dishwasher. #148796
    gegsy
    Participant

    Re: Bosch SGS43A12GB/27 dishwasher.

    Possible diverter unit situated on heater unit and/or module.
    Diverter unit comes complete with heater assembly.

    Heater Unit – 483058 – £60.00 GBP
    Module/PCB – 489607 – £70.00 GBP

    Greg

    in reply to: Diplomat ADP8242 power button does not function #148541
    gegsy
    Participant

    Re: Diplomat ADP8242 power button does not function

    Have you tried plugging something else into the socket the appliance is using??

    Greg

    in reply to: Bosch help needed, SGS5318GB/12 – not draining. #148140
    gegsy
    Participant

    Re: Bosch help needed, SGS5318GB/12 – not draining.

    Penguin45 wrote:Gratuitous bit of emboldening there Gegsy………. 😀

    Penguin45.

    Hadn’t noticed Chris 😉

Viewing 15 posts - 6,406 through 6,420 (of 6,724 total)