gegsy

Forum Replies Created

Viewing 15 posts - 796 through 810 (of 6,724 total)
  • Author
    Posts
  • in reply to: Bosch Classixx 1200 Express – not heating up the water #246130
    gegsy
    Participant

    Re: Bosch Classixx 1200 Express – not heating up the water

    It can also be a faulty NTC causing no heat.
    Even with a heating problem, these appliances will not fault, instead will continue cycle in cold water till the end.

    Greg

    in reply to: Barclays Premier League 2007-2008 / Champions League #221926
    gegsy
    Participant

    Re: Barclays Premier League 2007-2008 / Champions League

    Stop drooling at our lovelies 😆

    Greg

    in reply to: Barclays Premier League 2007-2008 / Champions League #221924
    gegsy
    Participant

    Re: Barclays Premier League 2007-2008 / Champions League

    ………..and has a huge budget on chewing gum 😀
    The Arsenal will surface again (hopefully 😕 ) to win the prem but Im not holding my breath 😛

    Greg

    in reply to: Bosch WVT1260GB bearing change #245882
    gegsy
    Participant

    Re: Bosch WVT1260GB bearing change

    Water seal usually has some grease on it (white stuff) on its inner face.
    Grease up slightly the bearing outers and drum shaft to make the job a tad easier.

    Greg

    in reply to: Bosch SGS 3062 GB/02 FD 8109 #246056
    gegsy
    Participant

    Re: Bosch SGS 3062 GB/02 FD 8109

    Maybe something in the drain pump area.
    Access is by removing filters and looking at the LHS of the sump recess to locate a torx 20 screw.
    Remove the cover that, that screw is holding and see if anything is in there that shouldn’t be.
    Bearing in mind it may be glass ❗

    Greg

    in reply to: Bosch WVF2402 not drying #246000
    gegsy
    Participant

    Re: Bosch WVF2402 not drying

    Hi
    Valve unit is p/no 173910 available from spares@ukwhitegoods.co.uk 😉
    As for container, its a bit of strip down but ok, just take your time 😀
    The conatiner below the fan will detatch from the top manifold of dryer and is the only bit that needs to be removed to be cleaned.

    Greg

    in reply to: Elba PX906 #246037
    gegsy
    Participant

    Re: Elba PX906

    Have a look here Here

    Greg

    in reply to: Bosch WVF2402 not drying #245998
    gegsy
    Participant

    Re: Bosch WVF2402 not drying

    Hi
    Things to check would be
    1/ The dryer fill valve should read app 2-3 kohms
    2/ Is the dryer fan, running correctly?
    3/ The condenser container below the dryer fan needs removing and may need cleaning.
    4/ Is the drain system clear ie waste pipe exit and filter unit on machine ?

    Power off before attempting any of this :plug:

    Greg

    in reply to: Bosch WVT1260GB bearing change #245880
    gegsy
    Participant

    Re: Bosch WVT1260GB bearing change

    Hi
    Yes, after looking at the other models in shop@, BS05109 will do the job.
    Odd that BSH don’t show a kit, would save a lot of money 👿

    Will get shop@ updated aswell Vendee, cheers.

    Greg

    in reply to: Barclays Premier League 2007-2008 / Champions League #221922
    gegsy
    Participant

    Re: Barclays Premier League 2007-2008 / Champions League

    👿 ……………mumbles something about Ian Wright,Nigel Winterburn,Dennis Berkamp and Kanu 😀
    What a shower of shit they are, come on lads, you get paid enough 😉

    Greg

    in reply to: Bosch WVT1260GB bearing change #245878
    gegsy
    Participant

    Re: Bosch WVT1260GB bearing change

    Bearings come with cross member p/no 283726 available from spares@ukwhitegoods.co.uk 😉
    Greg

    in reply to: Bosch SRS43C12 pathetic spray #245957
    gegsy
    Participant

    Re: Bosch SRS43C12 pathetic spray

    Just to make it clear 😀
    Bob has the water point system (it can jam and may also blow the module),
    Marks is just the basic heater unit,repair (most likely as Martin said) 😉

    Greg

    in reply to: Samsung Sensor Quick SWF-P10 #245977
    gegsy
    Participant

    Re: Samsung Sensor Quick SWF-P10

    Hi Bryan :waving:
    Alcopops 😯 Im teetotal like the rest of us on here 😆

    Greg

    in reply to: Samsung Sensor Quick SWF-P10 #245975
    gegsy
    Participant

    Re: Samsung Sensor Quick SWF-P10

    Hi
    E4 means you have an unbalanced load for whatever reason 😕
    Remember, no bath mats 😉

    Greg

    in reply to: Bosch SMS 6702 GB/09 #245949
    gegsy
    Participant

    Re: Bosch SMS 6702 GB/09

    Whilst that panel is off, it would be worth checking the wiring loom at the bottom, in the area where the door pivots.
    You will have to unwrap the sticky pouch 😀 and inspect the individual wires for damage.

    Greg

Viewing 15 posts - 796 through 810 (of 6,724 total)