gegsy

Forum Replies Created

Viewing 15 posts - 76 through 90 (of 6,724 total)
  • Author
    Posts
  • in reply to: Bosch wfl2260 active light #314854
    gegsy
    Participant

    Re: Bosch wfl2260 active light

    Yea after a period after door unlocks and ready if you switch off then back on 😉

    in reply to: Bosch wfl2260 active light #314852
    gegsy
    Participant

    Re: Bosch wfl2260 active light

    IIRC the active lamp stays lit for a while after door unlocks.
    If doesnt go to readty,possible coding/module error.

    Greg

    in reply to: Comet Service & Customer Aftercare #314320
    gegsy
    Participant

    Re: Comet Service & Customer Aftercare

    You aswell Chezza 🙁

    in reply to: bosch washer dryer model wvt126sgb/01 #314758
    gegsy
    Participant

    Re: bosch washer dryer model wvt126sgb/01

    Dryer water valve u/s ??

    Greg

    in reply to: samsung side by sides, controller info #302758
    gegsy
    Participant

    Re: samsung side by sides, controller info

    If you apply for trade access, you will probably get a lot more tech info 🙂

    Greg

    in reply to: Bosch SPS6462GB/06 stopping dead. #302814
    gegsy
    Participant

    Re: Bosch SPS6462GB/06 stopping dead.

    Broken wire/s in door loom at bottom of door bend?

    Greg

    in reply to: Bosch SGS43T62GB tripping #299621
    gegsy
    Participant

    Re: Bosch SGS43T62GB tripping

    Why not unplug appliance, remove r/h panel and check for visual damage to the supressor. Usually a blackened apprearance is a give away 😉

    Greg

    in reply to: Bosch KKU2901 Fridge too cold #298504
    gegsy
    Participant

    Re: Bosch KKU2901 Fridge too cold

    That model is spot on spimps 😕
    I would imagine you have a sticking diverter valve.
    This can only be changed by a refrigeration engineer as it entails breaking into the system to change.

    Greg

    in reply to: Whirlpool fault 3 flashes #298390
    gegsy
    Participant

    Re: Whirlpool fault 3 flashes

    Measure the heater with a suitable ohm meter 😉
    Unplug appliance first.
    Be looking for app 20-30 ohms reading.

    Greg

    in reply to: Bosch WFL12440GB/05 sump hose #299240
    gegsy
    Participant

    Re: Bosch WFL12440GB/05 sump hose

    Its getting there Jim ty 🙂

    Greg

    in reply to: siemens induction hob model eh777501e/04 #299258
    gegsy
    Participant

    Re: siemens induction hob model eh777501e/04

    E usually indicate over voltage of the mains supply.
    Let me know if its E??

    Greg

    in reply to: Bosch WFL12440GB/05 sump hose #299237
    gegsy
    Participant

    Re: Bosch WFL12440GB/05 sump hose

    No worries RM,
    The part has been changed to your latter 😉

    Greg

    in reply to: Bosch WFL12440GB/05 sump hose #299235
    gegsy
    Participant

    Re: Bosch WFL12440GB/05 sump hose

    Hi Jim
    P/no is 490649 for sump hose.
    Model is WFLI2440GB/05 😉

    Greg

    in reply to: Siemens SF25A061CB/15 slimline not draining #299073
    gegsy
    Participant

    Re: Siemens SF25A061CB/15 slimline not draining

    Very close its a SF25A061GB/15
    Torx Im afraid, take pump off and look for debris. The pumps are pretty robust IMHO.

    Power off if you are to investigate further :plug:

    Greg

    in reply to: bosch dishwasher #298951
    gegsy
    Participant

    Re: bosch dishwasher

    1/ Worth checking the microswitch in water tank on lhs for correct operation of contacts (with power off and ohm meter)
    2/ Have had the pcb in fascia (economy 7 timer) fail also.

    HTH
    Greg

Viewing 15 posts - 76 through 90 (of 6,724 total)