gegsy

Forum Replies Created

Viewing 15 posts - 1,036 through 1,050 (of 6,724 total)
1 2 3 … 69 70 71 … 447 448 449
  • Author
    Posts
  • February 1, 2008 at 8:29 pm in reply to: Bosch module 489607 #241902
    gegsy
    Participant

    Re: Bosch module 489607

    You can’t code a module unless you know what machine it goes in 😉

    Greg

    February 1, 2008 at 8:01 pm in reply to: MANUAL FOR SAMSUNG FRIDGE FREEZER #241756
    gegsy
    Participant

    Re: MANUAL FOR SAMSUNG FRIDGE FREEZER

    Ere Bryan, can you email it to Samsung aswell 😆

    Greg

    February 1, 2008 at 7:05 pm in reply to: Bosch GSG53C02GB/01 Sump filter stuck #241871
    gegsy
    Participant

    Re: Bosch GSG53C02GB/01 Sump filter stuck

    Can be on some, Ive only had two that wouldn’t play ball 😉

    Greg

    February 1, 2008 at 6:56 pm in reply to: Bosch GSG53C02GB/01 Sump filter stuck #241869
    gegsy
    Participant

    Re: Bosch GSG53C02GB/01 Sump filter stuck

    Hi
    Assuming model is SGS53C02GB/15 :con:
    The 3 part filter set is still p/no 435650 with no part change, so doent look like its been modified 😕

    Greg

    February 1, 2008 at 12:44 am in reply to: Choose a number… #241762
    gegsy
    Participant

    Re: Choose a number…

    😯 Webcam on 😆

    Greg

    January 31, 2008 at 11:46 pm in reply to: Bosch WFL Codes #241787
    gegsy
    Participant

    Re: Bosch WFL Codes

    :tup:

    January 31, 2008 at 11:38 pm in reply to: Bosch WFL Codes #241785
    gegsy
    Participant

    Re: Bosch WFL Codes

    Oh I see, in that case it basically timing out in the fill for whatever reason and by pressing the Start button again you are giving it a restart of the fill until it finally attains level required 😉

    Greg

    January 31, 2008 at 11:33 pm in reply to: MANUAL FOR SAMSUNG FRIDGE FREEZER #241753
    gegsy
    Participant

    Re: MANUAL FOR SAMSUNG FRIDGE FREEZER

    But not that one K 😕 may be its age

    Greg

    January 31, 2008 at 11:26 pm in reply to: Bosch WFL Codes #241783
    gegsy
    Participant

    Re: Bosch WFL Codes

    Best have the full model of machine to be sure 😉

    Greg

    FYI – Ready, Active and Finish usually indicates an NTC problem of sorts 😉

    January 31, 2008 at 11:22 pm in reply to: neff oven problems #241779
    gegsy
    Participant

    Re: neff oven problems

    You may be best, as you seem to have gone as far as you want 😕
    Try the repairs@ link on the left if required 😉

    Greg

    January 31, 2008 at 11:18 pm in reply to: Bosch fridge/freezer #241738
    gegsy
    Participant

    Re: Bosch fridge/freezer

    Yea it is but usually it dies completely not low temp 😕

    Greg

    January 31, 2008 at 11:13 pm in reply to: Choose a number… #241759
    gegsy
    Participant

    Re: Choose a number…

    69 😳

    January 31, 2008 at 11:08 pm in reply to: neff oven problems #241777
    gegsy
    Participant

    Re: neff oven problems

    Hi
    There will be a temp limiter that should read 0 ohms under normal conditions.
    Power off if you are to attempt fault finding :plug:

    Greg

    January 31, 2008 at 11:02 pm in reply to: Neff B1476N2GB/02 pyro oven dead. #241775
    gegsy
    Participant

    Re: Neff B1476N2GB/02 pyro oven dead.

    Hi Steve
    Check your email 😉

    Greg

    January 31, 2008 at 10:33 pm in reply to: Bosch fridge/freezer #241736
    gegsy
    Participant

    Re: Bosch fridge/freezer

    Have you considered a system problem 😕

    Greg

  • Author
    Posts
Viewing 15 posts - 1,036 through 1,050 (of 6,724 total)
1 2 3 … 69 70 71 … 447 448 449