jackster

Forum Replies Created

Viewing 15 posts - 16 through 30 (of 172 total)
  • Author
    Posts
  • in reply to: Whirlpool American fridge freezer #311169
    jackster
    Participant

    Re: Whirlpool American fridge freezer

    Rear PCB, they are shockingly bad.

    in reply to: ikea/whirlpool dwhb10w dishwasher fault #310740
    jackster
    Participant

    Re: ikea/whirlpool dwhb10w dishwasher fault

    The OWI (Optical water indicator) is in the 3 o’clock position in the sump, its a round black grill effect. They get crudded up, hot water and a tooth brush should sort it.

    in reply to: Whirlpool Wash Pump #310532
    jackster
    Participant

    Re: Whirlpool Wash Pump

    Hi,
    The model number is: 851175715810

    Would the old 481236158434 motor fit?

    Chay

    in reply to: whirlpool washing machine starts to fill then stops. #310245
    jackster
    Participant

    Re: whirlpool washing machine starts to fill then stops.

    Hi Mate, have you attempted a test programme on it?

    Press all option buttons

    Select Drain and then push start button until pump starts running

    Press first option button 4 times within 10 seconds

    The test then should start running.

    Off the top of my head the sequence lasts around 3 mins.

    If you want to jump through the options press the second button (so its in the out position) and then to move on to next press last option button and then for the rest press the first option twice each time you want to move on.

    Hope this helps,

    Chay

    in reply to: WHIRLPOOL DISHWASHER #310269
    jackster
    Participant

    Re: WHIRLPOOL DISHWASHER

    Hi Mate, the wiring loom runs from the pcb at the top down to the bottom, it will be that loom that gets trapped at the bottom as you open the door

    in reply to: whirlpool 3r awz480e #308428
    jackster
    Participant

    Re: whirlpool 3r awz480e

    The stat at the very back of the heater normally causes that problem, you get both in the pack so replace them and it should be away.

    in reply to: Whirlpool AWZ 7913 6th sense tumble dryers #308515
    jackster
    Participant

    Re: Whirlpool AWZ 7913 6th sense tumble dryers

    Is the m/c in an outhouse/cold room? They wont work below a certain temperature, not sure exactly what it is but ill dig it out and post it.

    in reply to: Engineer needed #306356
    jackster
    Participant

    Re: Engineer needed

    pm waiting

    in reply to: whirlpool d/w #307041
    jackster
    Participant

    Re: whirlpool d/w

    I have had this before and it turned out to be the NTC, if not check the base isnt flooded.

    in reply to: Whirlpool ADG7952 #306967
    jackster
    Participant

    Re: Whirlpool ADG7952

    I think the part you are looking for is;

    481227318056 – Wheel Fingertip

    in reply to: New World Oven #306756
    jackster
    Participant

    Re: New World Oven

    Cheers mate, sorted!

    in reply to: New World Oven #306754
    jackster
    Participant

    Re: New World Oven

    Anybody? The customer is pretty desperate to get it done before Christmas.
    Cheers all

    in reply to: Diplomat Dishwasher F4 fault #306567
    jackster
    Participant

    Re: Diplomat Dishwasher F4 fault

    Take the pump off at the bottom left side behind the panel, its a twist fit. It is likely that glass has got in there causing the impellar to jam.

    in reply to: Whirlpool fridge freezer fault codes please #306479
    jackster
    Participant

    Re: Whirlpool fridge freezer fault codes please

    Means it is due a new filter, if you keep the filter button pressed for a few seconds it resets to 99{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d}

    in reply to: Whirlpool AWZ7813 #306142
    jackster
    Participant

    Re: Whirlpool AWZ7813

    Have you got the 12nc, the 85….. no?

Viewing 15 posts - 16 through 30 (of 172 total)