Jantech

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 16 total)
1 2
  • Author
    Posts
  • October 21, 2025 at 2:47 pm in reply to: Peter Jay owner of PPJDomestics – desceased – Help with disposal of stock #493960
    Jantech
    Participant

    Just seen this, my deepest condolences, I knew Peter when working with Paul at Hatchgate and through the old elica network, always helped me out when I needed it.

    September 20, 2020 at 9:56 am in reply to: Vulkan Lokring #472079
    Jantech
    Participant

    Thanks Lawrence much appreciated

    February 14, 2019 at 11:46 am in reply to: Service Manual – Bosch Group Ovens #460537
    Jantech
    Participant

    Thanks Dave,

    I’ll grab one of the Enr numbers later and see if anyone has anything,

    cheers

    Jim

    November 21, 2018 at 12:05 pm in reply to: Samsung WF80F5E5U4X/EU #459082
    Jantech
    Participant

    Hey guys thanks for all your help, it was the motor that was faulty,

    cheers

    Jim

    November 15, 2018 at 4:15 pm in reply to: Samsung WF80F5E5U4X/EU #459079
    Jantech
    Participant

    Sorry doesn’t do a full a rotation!

    November 15, 2018 at 4:14 pm in reply to: Samsung WF80F5E5U4X/EU #459078
    Jantech
    Participant

    Hi Deltra, have already changed the board on this one, now the drum just judders and does do a full rotation, I have reset the machine by turning off for 30 mins and tried to run the calibration mode but it won’t complete as the drum won’t rotate, any one got any ideas?

    Thanks

    Jim

    June 27, 2018 at 7:07 pm in reply to: Indesit XWA91683 #456598
    Jantech
    Participant

    Re: Indesit XWA91683

    No child lock on this machine, checked instructions and none mentioned,

    Jim

    May 11, 2018 at 7:51 pm in reply to: Miele G5141 Dishwasher #455860
    Jantech
    Participant

    Re: Miele G5141 Dishwasher

    Tim/Dave, thanks for the info both excellent, I’m back there tomorrow so will use all you’ve given to get it working!

    Have a brilliant weekend

    Jim

    May 10, 2018 at 1:43 pm in reply to: Hotpoint WDAL 9640 G UK #455837
    Jantech
    Participant

    Re: Hotpoint WDAL 9640 G UK

    Hi Iadom,

    Yes open circuit, thanks for the advice, I’ll check it all out tomorrow.

    Thanks

    Jim

    April 9, 2018 at 7:49 am in reply to: Bosch Dishwasher SGS46E28GB/90 #455218
    Jantech
    Participant

    Re: Bosch Dishwasher SGS46E28GB/90

    Thanks Martin,

    Much appreciated, I’ll check the condition of the sensor.

    KR

    Jim

    October 10, 2017 at 4:48 pm in reply to: Whirlpool AWZ 612 Dryer Element #450896
    Jantech
    Participant

    Re: Whirlpool AWZ 612 Dryer Element

    Hi Dave,

    Can you send me a random one please – none of the machines have the 12nc number on anywhere.

    Thanks

    Jim

    October 6, 2017 at 9:41 am in reply to: Whirlpool AWZ 612 Dryer Element #450894
    Jantech
    Participant

    Re: Whirlpool AWZ 612 Dryer Element

    Hi Dave,

    Thanks for the info, I have got four connections to this heater and haven’t got any wiring information so don’t really know where to go from here, any ideas?

    Thanks

    Jim

    September 18, 2017 at 7:33 am in reply to: DAG ( Domestic & General ) #444147
    Jantech
    Participant

    Re: DAG ( Domestic & General )

    Same story for us, out of the blue the letter arrives! Restructuring!

    I also wastes half a day on there ‘training’ so have to agree with Chris, be very wary.

    Jim

    July 21, 2017 at 4:03 pm in reply to: Neff Integrated Dishwasher #449086
    Jantech
    Participant

    Re: Neff Integrated Dishwasher

    Thanks Martin,

    Much appreciated, was beginning to lose the will to live!

    Flashing red light so I’ll check the bits you suggested,

    Have a good weekend,

    Jim

    April 28, 2017 at 6:58 pm in reply to: D&G PORTAL SYSTEM #445429
    Jantech
    Participant

    Re: D&G PORTAL SYSTEM

    Hi all,

    I’ve been on since February, it’s a pain to use but I have muddled through, although since beginning of April I’ve not had many jobs through probably due to lack of available slots, kept mine low so not to over promise myself, seems I’ve have missed out on a lot of work!

    Anyone else had work drop off?

  • Author
    Posts
Viewing 15 posts - 1 through 15 (of 16 total)
1 2